Complete Rebuild Kit for Roadmaster Falcon 2 Tow Bar

Question

Question:

Im looking for a complete rebuild kit for a Roadmaster Falcon2, RV hitch #043038. Will your kit # RM910003-55 work, or is their a different kit? Thanks

asked by: Martin G

0

Expert Reply:

Since you have a Falcon 2 tow bar the correct rebuild kit you'd need is the part # RM-910003-60 actually. The part number you mentioned is for the All Terrain model.

expert reply by: Jameson C

0

Answer 1

When it comes to the load stops for your Rhino Rack Platform you would need The Load Stops for Rhino-Rack Vortex Aero Crossbars or Pioneer Platform Rack - 5 inch Tall - Qty 2 #RRRLH2. The RRRLH1 will not work. These load stops will help hold gear in…

view full answer...

Answer 2

In order to carry kayaks on a 2021 Jeep Gladiator (Hard Top) you'll need to start with a roof rack. For this, I recommend the Exposed Racks Roof Rack part #ER77FR. This system simply clamps onto the gutters and then provides two crossbars capable…

view full answer...

Answer 3

Over time, dirt and debris can build up on the retracting portion of the tow bar arms. When the arms retract, this dirt is carried into the interior of the tow bar, and can foul out the locking mechanism on one or both of the tow bar arms. This is…

view full answer...

Answer 4

Your memory does serve you right and both arms on your Roadmaster Falcon 2 #RM-520 are designed to "lock up" as this is not a non-binding tow bar; whether or not they've been able to get the arms to lock without performing the two sharp…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Tim, the correct rebuild kit for a Roadmaster Falcon All Terrain tow bar like you have is the part #RM910003-85. How many miles do you have on your tow bar you think?

view full answer...

Answer 8

What you would need is the part #RM910003-32 for the bolts, the part #RM-200029-10 for the bushing and then for the yoke part #RM910575 and you'd be set. There isn't an entire kit that covers all the parts you need but with these three part…

view full answer...

Answer 9

I do have almost everything you will need to repair your Roadmaster Sterling Tow Bar SN #005384 but after speaking with my representative at Roadmaster, they strongly advised me that you should replace the tow bar due to the sheer age of the unit and…

view full answer...

Answer 10

Yes, the Inner Arm Bushing Kit for Roadmaster Sterling Tow Bars #RM-910003-40 and the Complete Repair Kit for Roadmaster Sterling Tow Bar #RM-910003-30 are both correct for your Roadmaster Sterling tow bar that has a serial number 11019.

view full answer...

Answer 11

Hello Robert, thanks for reaching out. We do offer a repair kit for the Roadmaster Sterling tow bar, the Complete Repair Kit for Roadmaster Nighthawk, Sterling, and Sterling All-Terrain Tow Bars #RM-910003-30. This includes new shoulder bolts, nuts,…

view full answer...

Answer 12

The inner arm is the same for both sides on the Falcon 2 #RM-520. If you replaced the outer arm assembly it would be the #910021-12 for the driver side and #910021-22 for the passenger side. The replacement outer arm bushings are the #RM95FR. These…

view full answer...

Complete Rebuild Kit for Roadmaster Falcon 2 Tow Bar

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching