I.D. and O.D. of Replacement Bearing for etrailer and Ram Round, Topwind Jacks

Question

Question:

Your QandA on part number contradict each other on question 2 and 3 answers. Part number TJA-2000-BR what is the OD and ID of this thrust bearing?

asked by: Ken T

0

Expert Reply:

I went out to our warehouse for you to double check, the Replacement Bearing for etrailer and Ram Round, Topwind Jacks part # TJA-2000-BR has an I.D. of .50" and an O.D. of 1.025".

expert reply by: Conner L

0

I.D. and O.D. of Replacement Bearing for etrailer and Ram Round, Topwind Jacks
(click to enlarge)

Answer 1

We carry a 2-1/2 inch Lunette ring that has a four hole flat mount base, item #C48550. Other than that our Lunette rings are 3 inches. We do have other couplers that bolt to your trailer tongue, like part #DM12141-81. I've also linked the rest of…

view full answer...

Answer 2

Hey Steve, thanks for the information. I tripled checked this but for whatever reason, Carry-On put a 2,000 lbs E-Z Lube axle pn 2K7158EZ on your 5' x 8' SP Series trailer and then decided to put spindles on it (pn 151T) that are not EZ-Lube.…

view full answer...

Answer 3

Hey Eric, so we do have what you need with the replacement cap part #VA55JR but the one you mentioned is smaller so it would not work for you. The cap you need is 4 inch diameter and the one you referenced is 3.75 inch.

view full answer...

Answer 4

Atwood parts are not available as they are no longer around as a business, but we do have a thrust bearing with a similar dimension to the one you mentioned. I cannot guarantee it will work, but you may want to consider the Replacement Bearing for…

view full answer...

Answer 5

The inner diameter (ID) of the Replacement Thrust Bearing part #BD500223 is 0.525". The ID of the Replacement Thrust Bearing part #TJA-2000-BR is 0.500". With that being said it looks like the part ending in "BR" would be the best…

view full answer...

Answer 6

I took a look at our available thrust bearings for Bulldog jacks, and I the closest I was able to find to your measurements is the Replacement Thrust Bearing for 5,000-lb Capacity Bulldog Jacks #BD500223. This bearing has an inside diameter of…

view full answer...

Answer 7

The bearing part #L44649 has an inner diameter of 1.063 and is typically used in 3,500 lb axle hubs and the #L44643 has an inner diameter of 1 inch and is typically used on 2,000 lb axle hubs. If you can get me more info on your trailer like axle…

view full answer...

Answer 8

Hi George; there are some replacement parts available for the Fulton F2 Boat Trailer Jack #F1413020134. We have the following: -Replacement Handle and Crank Kit for Fulton F2 Swing-Up Jacks #F500134 -Replacement Pull Pin Kit for Fulton F2 Swing-Up…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

I.D. and O.D. of Replacement Bearing for etrailer and Ram Round, Topwind Jacks

Product Page this Question was Asked From

Continue Researching