Recommended SnapPads For A Lippert Ground Control 3.0 Leveling System

Question

Question:

Looking for a Lippert 3.0 Ground Control jack pad with the square tubing connection.

asked by: Keith L

0

Expert Reply:

Jack feet # LC377962 for the Lippert Ground Control 3.0 # LC675817 are typically 9" in diameter and round and would require SnapPads like part # SP54FR6. I recommend measuring each of the jack feet to ensure that they're all the same and 9" in diameter so that you order the correct pads. If yours differ in size or shape then let me know what you have and I'd be happy to find the correct fit.

expert reply by: Kevin C

0

Answer 1

The Air Lift WirelessONE Compressor System #AL25980EZ and Air Lift WirelessONE Compressor System #AL25980 are nearly identical with only some very minor differences in CFM and duty cycle ratings. The #AL25980EZ will also come with an easier mounting…

view full answer...

Answer 2

Hey Donna, yes the ends of the Camco RhinoEXTREME RV Sewer Hose #CAM39863 are removable and are designed to be easily removed for storage reasons like what you mentioned.

view full answer...

Answer 3

Hey Dennis! The brackets on the Valterra EZ Hose Carrier #A04-0155XBK are fixed in place on the tube and aren’t designed to be repositioned. Each bracket has a fixed mounting hole spacing of 5-1/4" on center as well. What kind of trailer are you…

view full answer...

Answer 4

The RhinoEXTREME RV Sewer Hose Extension part #CAM39863 has a collapsed length of about 5' 6" it compresses almost 50% of its extended size.

view full answer...

Answer 5

Determining which SnapPads fit your 2022 Grand Design Solitude 380FL, the diameter of each jack foot needs to be measured and determine the shape of the foot. Note that it is not uncommon for different shapes and sizes to be used between the front…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Recommended SnapPads For A Lippert Ground Control 3.0 Leveling System

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching