Recommendations To Ensure Water Does Not Get Into Hubs & Rust Bearings On Boat Trailer Is Salt Water

Question

Question:

I launch almost 100 of the time in salt water. How can I know that the bearings will not rust?

asked by: Jerry

0

Expert Reply:

The best way to prevent rust and corrosion inside your hubs is by selecting a stainless steel hub like the Kodiak # KH84545S, and more frequently inspecting your bearings and seals. Be sure your hubs are filled with a marine grade Grease # L54FR. You can also use Bearing Buddy Bearing Protectors # BB1980A-SS if you do not have an easy lube spindle. The bearing buddy will allow you to ensure your hub is filled completely with grease leaving no room for water to get in.

If you can provide me additional details on your trailer I can help you know which hubs, Bearing Buddy's, bearings and seals you may need for your trailer.

expert reply by: Bud M

0

Answer 1

Hi James; the capacity listed for the Westlake ST205/75R14 Radial Tire w 14" Eagle Aluminum Wheel #WST59FR is for each individual wheel and tire. If you had a pair of them you add the capacity together so the wheels could hold 4,400 lbs and the…

view full answer...

Answer 2

I have a few options for you to help with identifying the hub on your trailer. The first and easiest method would be to crawl under the trailer and look for the axle tag on the beam. This should give an axle capacity which we can then use to find the…

view full answer...

Answer 3

From what I have found, the Dexter 80043A spindle on your trailer matches your standard 3,500 lb axle bearings and grease seal. It uses a #L68149 inner and #L44649 outer bearing with a #58846 grease seal. This is also true for the Kodiak Trailer Hub…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Recommendations To Ensure Water Does Not Get Into Hubs & Rust Bearings On Boat Trailer Is Salt Water

Products Featured in This Question

Continue Researching