Furrion Side Cameras Come On When Brake Pedal is Pressed
Updated 03/30/2024 | Published 04/20/2023
Question:
Furrion 7s camera system with side view. Wired side view cameras with trigger signals as per prints. Problem: touch my breaks and either the right or left camera comes on. It works fine when I turn on the blinkers.
asked by: Alan H
Expert Reply:
In regards to the LED Marker Light RV Side Cameras part # FCE48TASL, there are only three wires you should be using. The brown and red wire get tied together and then attached to the running light power wire coming from the old light, the black wire get tied into the ground wire coming from the old light. I recommend checking over all the wiring to ensure you have it wired as such. I did a video on this exact process if you want to fast forward to the 10:00 mark in the video linked below.
Statick
3/30/2024
Mine does this as well and it’s frustrating! I didn’t change any of the wiring since the instructions indicate we could ‘plug and play’ by sliding the camera into the existing side marker. Makes it very hard to use the rear camera for backing up and I’ll be contacting Furrion.
Product Page this Question was Asked From
LED Marker Light RV Side Cameras w/ Night Vision for Furrion Vision S Systems - Qty 2
- Accessories and Parts
- RV Camera System
- Camera
- Side Camera
- Right Side Camera
- Left Side Camera
- Black
- Furrion
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Troubleshooting A Furrion Camera System That Switches To Side Cameras When The Brakes Are Applied
- Q&A: Replacement Trailer Clearance Lights for GloBrite 122r/122y
- Q&A: Correct Hinge Type for Replacement Roof Vent
- Shop: Base Plate for Tow Bar
- Search Results: spare tire carrier
- Q&A: Replacement Circuit Board for a 4700 Model MaxxAir Roof Vent
- Shop: Brake Controller
- Shop: Trailer Hitch
- Q&A: Recommended Clearance Dimensions Between Truck Bed Rails and 5th Wheel Trailer
- Shop: Dexter DX7.5 Drop-N-Go Brake Actuator - Drum Brakes - 2" Ball - Zinc Plated - 7,500 lbs
- Shop: Roadmaster Crossbar-Style Base Plate Kit - Removable Arms
- Shop: etrailer Spare Tire Mount for Hitch - 2" Hitch
- Shop: Roadmaster Hitch Spare Tire Mount with 2" Receiver Opening - 2" Hitches
- Shop: Camco Replacement Lid for Jensen RV Roof Vent w/ Pin-Style Hinge - Polypropylene - White
- Shop: Replacement Printed Circuit Board for MaxxAir Powered Lift RV Roof Vents w/ Reversible Fan
- Shop: Free-Swinging RV Cabinet Hinges - Flush Mount - Satin Nickel - Qty 2
- Q&A: Recommended Replacement For A Suburban SW6 DE RV Water Heater
- Shop: Trailer Wiring
- Search Results: rubber flooring
- Q&A: Does Install of Curt Hitch on 1991 Ford E-150 Require Drilling
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Video: An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Search Results: trailer wiring
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Suspension Enhancement
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Search Results: trailer tires and wheels
on Accessories and Parts
Toni R.
3/13/2024
Yeah, checked and double checked and I have the same problem. Has anyone found a solution? I even went in and made sure I had independent grounds, traced to the 7 pin and everything is as the instructions say, but I still get one camera or thenl other when the brakes are pushed.