Replacement For T1401 Boat Trailer Winch

Question

Question:

I have the T1401 boat trailer winch that I want to replace I don’t see that winch on your website, what is the best replacement

asked by: Mike

0

Expert Reply:

The T1401 has been discontinued but based on my research that is a 1,400 lb winch with a 20 foot strap. To replace it, the best option is the very similar Fulton Trailer Winch # F142201.

The # F142201 is a 1,500 lb winch that also uses a 20 foot strap; you can use your current strap or a new one with part # DL24260.

expert reply by: Kyle S

0

Answer 1

Since you currently have a 1500 lb capacity winch, I'd recommend staying with that capacity, as long as it's working well for you. Since you're using the winch to pull a boat up on a trailer, I'd recommend using a winch with a strap,…

view full answer...

Answer 2

Fulton makes high quality winches like the Fulton Winch #F142201 that you referenced. JIF Marine makes great winches too and the Single-Speed Boat Trailer Winch #315-W2000D is almost an identical design except for it comes with a 20 foot cable and a…

view full answer...

Answer 3

The bolt hole dimensions on the bottom of the Jif Marine Single-Speed Boat Trailer Winch with 20' Strap and Brake item #315-W2000D are 2.5 inches apart center to center. The attachment point to the center bolt is a slot that is 3.5 inches - 5…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Replacement For T1401 Boat Trailer Winch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching