Wiring Diagram Tekonsha Voyager Brake Controller # 39510

Question

Question:

I need a wiring diagram for a tekonsha voyager electronic brake control can some one please help me?

asked by: Russell

0

Expert Reply:

Yes we can help. To the right there is a picture that has a diagram of how most brake controllers wire up, if you click it you will be able to see an enlarged version of the picture. Below you will find a link to the installation instructions and to wiring instructions for wiring brake controllers. All brake controllers wire pretty much the same with a white ground wire, a black power wire a red brake switch wire and a blue brake feed wire that goes to the trailer brakes.

If you would like to give some information about your vehicle, I could make a more specific recommendation on how to wire it and let you know if any other parts are needed. I would need the year, make, and model of your truck along with the type of trailer connector you have at the rear of the vehicle.

expert reply by: Robert G

0

click to enlarge

John T.

1/29/2013

I have a 2006 chevy suburban equipted w a trailer package, I have the wiring harness to install on to my Tekonsha voyager brake controller. The problem I have is there are 5 wires on the wiring harness and only 4 on the controller. Wiring harness Dk.Blue - trailer brake controller switched outputRed - Fused trailer brake controller battery feedBlack - Brake controller groundLt Blue - Vehicle stop lamp switch to brake controller input Brown - Brake controller illuminationcontroller wires Red, white, blue, and blackplease let me know what wires go where. ThanksJohn

Patrick B.

2/8/2013

With your 2006 Suburban, you should have a plug-in port that you can use with part 3015-P so that you do not have to splice wires or use the factory included pigtail. This will simplify the whole installation. If you do not want to use the plug in harness, the splicing operation is still pretty simple. You would make the following connections. Truck Wire - Function - Brake Control Wire Dk. Blue - Brake Ctl Ouptut - Blue Red - Fused Battery Feed - Black Black - Brake Ctl Ground - White Lt Blue - Vehicle Stop Lamp - Red Brown - Illumination - Not Used

Answer 1

On each individual electric brake magnet the amperage draw would be 3.0 to 3.2 max amps at 12 to 13 volts on 7-inch brake magnets and 3.2 to 4.0 max amps at 12 to 13 volts on 10 and 12-inch brake magnets. The max amperage draw for the brake magnets…

view full answer...

Answer 2

That is the only way you'd be able to install the Tekonsha Prodigy P3 Trailer Brake Controller #90195 on your 2023 Ford Transit T350 since there is no custom fit wiring harness. To install this, you'll first need to find the cold side of the…

view full answer...

Answer 3

Beginning with the introduction of the 2007 model year, GM stopped using the connector that was located in the convenience center under the dash for installing a brake controller. Instead, the tow package connection consists of 4 or 5 wires bundled…

view full answer...

Answer 4

Unfortunately that 12 pin rectangular plug has nothing to do with the trailer wiring harness. To add a 7-way and 4-way connector to your 2023 Chevy Express Cargo van you're going to need to buy two separate harnesses. The reason for this is that…

view full answer...

Answer 5

I have attached a basic brake controller wiring diagram for you. You will want to make sure that you ground the white wire to the negative post on the battery. The black wire will attach to the positive battery post. The red wire will tap into the…

view full answer...

Answer 6

I did some research and found that the 12194TC seal you said you have measures 1.250 inside diameter, and 1.979 outside diameter. The seal I recommend is part #34823. The dimensions listed for this seal are 1.249 inside diameter and 1.983 outside…

view full answer...

Answer 7

Thanks for reaching out and providing a photo, Christian! Instead of getting the plain Hopkins Connector #HM40975 what you need is the Hopkins Kit #HM40975-11998 which not only has the exact same 4-Way/7-Way connector system, but it also has the…

view full answer...

Answer 8

Thanks for the photo and let's start with the correct 4-way for your 2020 Chevy Express 2500, which is the T-One Vehicle Wiring Harness #118392. As you can see by the cut out of the linked installation instructions I added, you will connect the…

view full answer...

Answer 9

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 10

When you unhook the trailer from the SUV you are not going to pull the pin of the breakaway switch to activate the trailer brakes. The only time the breakaway switch is going to pull power is if the pin is pulled from the breakaway switch which…

view full answer...

Answer 11

It sounds like you have everything wired correctly to bench test. To bench test a brake controller you need to connect the black wire from the Tekonsha Voyager Trailer Brake Controller #39510 to the positive terminal of a 12 volt battery and the…

view full answer...

Answer 12

Manufacturers can use any colors they want since there isn't really a standard for wire color and function. You will need to test each of the wires using a circuit tester such as #PTW2993 to determine the functions. Then you can attach them to…

view full answer...

Wiring Diagram Tekonsha Voyager Brake Controller # 39510

Featured Help Information

Miscellaneous Media

Continue Researching