How Many 2-1/2 Long Standard Torx Screws Come In The Package?

Question

Question:

how are theses packaged, what quantities?

asked by: Alan S

0

Expert Reply:

The 2-1/2" Long Standard Torx Trailer Floor and Wall Liner Screw # TFX250 is listed for a single screw so you can order the exact quantity you need. We do offer the 2-1/2" Long Torx Floor Screws in a Package of 40 # TF01250 which are the same height and diameter. Both these require a 7/32" Drill Bit for the pilot hole and a T30 Torx Bit # TX430-1

expert reply by: Bud M

0

Answer 1

We have a few sizes of Torx screws to secure the bed boards on a trailer, however I do not know what screws are used on the Big Tex trailers and we do not have any specifically for them. I have included the length options we carry below, they all…

view full answer...

Answer 2

The 2-1/2" Long Torx Floor Screws, 40/Pkg #TF01250 is a great way to purchase the screws in bulk. Additional screws are available individually as part #TFX250.

view full answer...

Answer 3

You are correct. The pilot hole size for the Torx Floor Screws, part #TF01250, is 7/32 inch. These come with 40 screws in the package, and measure 2-1/2 inches long. The screwdriver bit you may want for the Torx screws is part #TX430-1. These are…

view full answer...

Answer 4

The 2-1/2" Long Torx Floor Screws #TF01250 length is measured at the threads (see attached photo). Attached is a review video where we go over this as well for you to check out.

view full answer...

Answer 5

We do offer deck screws which can be ordered in bulk, you'll first however need to know what size you need. The Torx Floor Screws for example are 1/4" diameter and offered in a few different lengths; part #TF01150 for 1-1/2" long, part…

view full answer...

Answer 6

I would recommend to use the treated torx screws for ACQ (Alkaline Copper Quaternary) treated wood for better corrosion and rust resistance. The treated torx screws like the Redline 2-1/2 Inch Long Torx Trailer Screw for ACQ Treated Wood, part…

view full answer...

Answer 7

There really isn't anything we can offer other than using screws longer than the 1-1/2 inch Torx Floor Screws #TF01150 since that particular length isn't catching. Depending the added length you need you can get the same screws, but either…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

How Many 2-1/2 Long Standard Torx Screws Come In The Package?

Product Page this Question was Asked From

Continue Researching