Dimensions Of The MB STurgis Vertical 2-Stage Propane Regulator # 108220

Question

Question:

What are the physical dimensions of this regulator?

asked by: Chris A

1

Helpful Expert Reply:

The MB Sturgis Vertical 2-Stage Propane Regulator # 108220 is approximately 6-1/4" in total length. At its widest points is is 2-3/4" wide by 2-3/4" deep.

expert reply by: Kevin C

1

108220 Dimensions
(click to enlarge)

Answer 1

The MB Sturgis #108220 propane regulator can maintain 11" water column and up to 400,000 BTU/Hour. The only propane valve we have is part of a quick connect fitting like the Camco #CAM59853 for low pressure propane systems. If you need something…

view full answer...

Answer 2

Thanks for reaching out, Tara! In order to connect the MB Sturgis Vertical 2-Stage Propane Regulator #108220 to your propane tank and your 2018 Zinger Lite you'll need the following hoses: - Pigtail #100473-24-MBS (from tank to regulator) - Hose…

view full answer...

Answer 3

Those three regulators are all very similar and essentially do the same thing but they're used on different propane setups. Part #37207-30365 is a vertical regulator. Vertical regulators are commonly on propane systems on travel trailers or pop…

view full answer...

Answer 4

I looked up the specs of the Fairview GR-9959 and they do have the same fittings so you an use the MB Sturgis Horizontal 2-Stage Propane Regulator #108221 as a replacement. Both have the 1/4" female NPT inlet and 3/8" female NPT outlet. I…

view full answer...

Answer 5

For your Draw Tite Activator brake controller like #5504 I found the setup instructions and they are below for you to check out. 1. With a trailer connected, set the sync control half way between + and -. Starting with the output control in the…

view full answer...

Answer 6

The troubleshooting guide for the (discontinued) Draw-Tite Activator II 5500 is actually the same as the Draw-Tite Activator IV #5504. The instructions (with the troubleshooting guide) for the Activator IV are linked for you to reference but I have…

view full answer...

Answer 7

For your propane tank with fill valve, you most likely need the Camco Horizontal 2-Stage Propane Regulator w/ P.O.L - 160,000 Btu/Hr #CAM59333. This will have the 1/4 inch NPt inlet and the 3/8 NPT outlet and will maintain a constant 11 inch water…

view full answer...

Answer 8

Hey Matt! The best regulator for your 100 lb Propane Tank is the MB Sturgis Horizontal 2-Stage Propane Regulator #108221. You should be able to hook the regulator up to your tank using the MB Sturgis Propane Pigtail Hose #100019-60 and Adapter…

view full answer...

Answer 9

Camco part #CAM59333 will work as a replacement for your Marshall 260 Horizontal LP regulator. It includes a P.O.L. connector. If you do not need the P.O.L. connector then you can use the Camco Horizontal 2-Stage Propane Regulator #CAM59323. Your…

view full answer...

Answer 10

Yes, the part #CAM59333 will work as a replacement for your Marshall 260 LP regulator. Keep in mind that it does have the P.O.L. connector included. If you do not need the P.O.L. connector then you will want to go with the Camco Horizontal 2-Stage…

view full answer...

Answer 11

I have exactly what you need. There is nothing special about the Marshall Model 260 Propane Regulator so you can use pretty much any dual stage regulator. I recommend either the MB Sturgis Vertical 2-Stage Propane Regulator Part #108220 or the Camco…

view full answer...

Answer 12

Your Marshall brass regulator 260 can easily be replaced with a Camco 2 Stage regulator part #CAM59323. Your current regulator is basically just a standard style dual stage regulator like this.

view full answer...

Dimensions Of The MB STurgis Vertical 2-Stage Propane Regulator # 108220

Featured Help Information

Miscellaneous Media

Continue Researching