Mounting Hole Dimensions of the Camco AccuLevel Trailer Bubble Level item # CAM25563

Question

Question:

What is the mounting hole pattern on level CAM25563?

asked by: Matthew D

0

Expert Reply:

I went out to the warehouse and measured the Camco AccuLevel Trailer Bubble Level item # CAM25563. The mounting holes are 10-3/4" x 1-3/4". The holes are oblong and are a 1/2" long vertically. I took the measurements from the center of the holes.

I have linked a diagram I made below.

expert reply by: Jerred H

0

Camco AccuLevel Trailer Bubble Level item # CAM25563
(click to enlarge)

Answer 1

The Camco AccuLevel Trailer Bubble Level #CAM25563 is measured in degrees so that it will be compatible with multiple trailer sizes.

view full answer...

Answer 2

The overall length of the Camco AccuLevel Trailer Bubble Level #CAM25563 is 10 inches in length overall and 3 inches tall.

view full answer...

Answer 3

I do have an option for you but the Camco AccuLevel Trailer Bubble Level part #CAM25563 does not come with brackets or hardware to install. I recommend Wheel Masters Level Master Trailer Bubble Level with 5th Wheel Pin Box Mounting Bracket part…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Mounting Hole Dimensions of the Camco AccuLevel Trailer Bubble Level item # CAM25563

Product Page this Question was Asked From

Continue Researching