Optronics Trailer Clearance Light Similar to AL 91RB that Installs With Smaller Hole Drilled
Published 01/11/2023
Products Featured in This Question
Question:
I am planning on using a red marker light to mount on my aluminum trailer for a rear side marker. Im considering getting the optronics a91rb with the a91bob mount. The mount will be flush to the surface. Will the right angle pigtail plug fit between the mounting surface and the light or protrude from the bottom requiring clearancing underneath. I would prefer to just drill a small hole for the wiring and not a large hole to clearance for the plug. It appears the other option is to get an al82rb and not use a right angle plug. Thanks for your assistance.
asked by: Trey E
Expert Reply:
The Optronics clearance light part # AL91RB in all of it's configurations would require a hole to be drilled for a harness like the part # A46PB to install with a grommet like the part # A91BOB. There isn't a way to mount it flush without drilling. If you used the part # MCL67RBCB instead though it would require a much smaller hole be drilled since the entire harness of the other setup gets ran through the hole.
Product Page this Question was Asked From
Optronics ThinLine Clearance or Side Marker Light w/ Chrome Bracket - Submersible - 3 Diodes - Red
- Trailer Lights
- Clearance Lights
- Marker
- Rectangle
- Surface Mount
- Submersible Lights
- LED Light
- 4-1/8 Inch x 1-1/4 Inch
- Red
- Optronics
more information >
Continue Researching
- Video: Feature Breakdown: Mounting Bracket for Optronics 90 Series or 91 Series Trailer Lights
- Video: Optronics Trailer Lights A91BOB Review
- Video: All You Need to Know About the 2" Round Grommet
- Video: Optronics Sealed Thin Line Two-Bulb Trailer Clearance Light Installation
- Search Results: trailer lights
- Search Results: a54gb
- Search Results: mcl75ab
- Search Results: 56232
- Search Results: mcl75rb
- Search Results: a46pb
- Search Results: al91rb
- Shop: Optronics LED Trailer Clearance or Side Marker Light - Submersible - 3 Diodes - Round - Red Lens
- Shop: 16 Gauge, 4 Conductor Jacketed Wire - Per Foot
- Shop: LED Trailer Fender Light - 2 Diodes - Amber and Red Lens
- Shop: 20 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 30" Ground
- Q&A: Availability of Trailer Taillight ID Bar that Has LEDs
- Q&A: Does Optronics Mini Thin Line LED Marker/Clearance Light # AL191AB Use Grommet # A91GB
- Q&A: Does The Optronics LED Side Marker Light # AL91AB have 2 Male Connector Posts
- Q&A: What Size Hole is Needed to Install the LED Trailer Clearance/Side Marker Light
- Q&A: Can I Get 100 Feet Of Bonded 4 Wire For My Trailer?
- Q&A: How Does Part A91BOB Mount To The Trailer and Are The Lights It Holds Submersible
- Q&A: Availability Of White Replacement Fender For 2003 Shoreland'r Trailer W/ ST205/75R15 Tires
- Shop: Plug - Single Wire with 12" Lead for A91 and AL91 Series Trailer Clearance, Side Marker Lights
- Shop: Thinline LED Clearance and Side Marker Light - Submersible - 3 Diodes - Rectangle - Red
- Shop: Optronics Thinline LED Trailer Clearance or Side Marker Light - Submersible - 4 Diodes - Red Lens
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Video: Measuring To Choose The Right Trailer Axle
on Trailer Lights
