Longer Ball Mount that Fits 1-1/4 inch Trailer Hitch
Published 11/22/2022
Products Featured in This Question
Question:
Jameson While it has been hard to fine a very level surface to check the hitch receiver height measurement at this time it appears the closest drop measurement available that at least comes close to the actual measurements from top of receiver to bottom of coupler is going to be a 1.25” drop ball mount. Can you suggest based on that which Curt 1.25” ball mount will be the longest to meet that requirement? I believe from looking on Curt’s website this might be the one that is longest with the expectected required drop. #45519
asked by: Dave
Expert Reply:
A longer ball mount would be a decent idea I would think but since its going to be a Class II 1-1/4 inch ball there aren't super long options. Mostly everything will be about same length with some variations. If you can determine the rise/drop you need I can let you know what longest option would be.
(click to enlarge)
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- For Towing
- Class II
- 350 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Search Results: hitch pins and clips
- Shop: Brake Controller
- Shop: Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - Up to 2 Axles - Proportional
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Trailer Hitch Extender for 1-1/4" Trailer Hitch Receivers - 7" Long
- Search Results: trailer hitch lock
- Search Results: lock n roll trailer hitch ball mount
- Search Results: trailer ball locks
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Parts Needed to Install 7-Way on 2021 Subaru Outback Wagon
- Q&A: Parts Needed To Add 7-Way And Brake Controller To 2025 Subaru Outback XT
- Video: How to Install: Curt Echo Wireless Brake Controller on your 2020 Subaru Outback Wagon
- Video: etrailer Trailer Brake Controller 7-Way RV Upgrade Kit Installation - 2020 Subaru Outback Wagon
- Video: Curt No-Drill Bracket Review
- Search Results: 30 amp fuse
- Search Results: trailer hitch ball mount
- Q&A: Does the Yakima Kayak Carrier Fit on Overhaul HD Crossbars?
- Search Results: flat tow brake system
- Shop: 7-Way RV Upgrade Kit for Trailer Brake Controller Installation - 12 Gauge Wires
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional
- Q&A: Ball Mount that Fits 1-1/4 inch Hitch with 2 inch Hitch Ball
- Q&A: What T-Slot Saddle Kayak Carrier Do You Recommend for an Adarac Ladder Rack?
- Q&A: Recommended Roof Rack and Kayak Carrier for a 2014 Nissan Verse Note
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
on Trailer Hitch
Dave
11/22/2022
Jameson While it has been hard to fine a very level surface to check the hitch receiver height measurement at this time it appears the closest drop measurement available that at least comes close to the actual measurements from top of receiver to bottom of coupler is going to be a 1.25” drop ball mount. Can you suggest based on that which Curt 1.25” ball mount will be the longest to meet that requirement? I believe from looking on Curt’s website this might be the one that is longest with the expectected required drop. #45519