Depth Of The LaSalle Bristol And Valterra Sewer Lug To Flange Adapters

Question

Question:

What is the depth of the fitting from the flange to the outer edge of the bayonet side? Is this dimension the same in the La Salle version as the Valterra version.

asked by: Jennie B

0

Expert Reply:

The depth of the 3" tube to the flange on the LaSalle Bristol RV Lug Adapter with Flange # 34466V13B is approximately 1-1/4" deep. The Valterra RV Sewer Lug Fitting with Flange # T1009 has a 1-1/8" depth, which is the only difference between the two flanges.

expert reply by: Kevin C

0

T1009 Depth
(click to enlarge)

34466V13B Depth
(click to enlarge)

Answer 1

We have the LaSalle #34466V153 which will slide on over your 1-1/2" pipe to give you 3" pipe. From here you can use #T1028 to give you the bayonet fitting you're needing. Use the solvent cement #3447530889 to complete installation and…

view full answer...

Answer 2

The difference between hubs and spigots in terms of RV waste valves like the part #T40A is that hubs fit over pipes and spigots fit into them instead. So it really comes down to if you have a preference but the #T40A is a spigot on both sides.

view full answer...

Answer 3

We have the LaSalle Bristol Eccentric Tank Reducer #34466V153 which can slide over your 1-1/2 inch diameter gray pipe to give you a 3 inch pipe that you could then attach the 3 inch pipe to 3 inch bayonet adapter part #T1028 and you'd be set.

view full answer...

Answer 4

If I'm understanding you correctly, you want a bayonet flange that will attach to this fitting and allow you to attach your RV hose. To accomplish this, you will want to use the 3" bayonet Flange #T1009 . If you need any ABS Cement you can…

view full answer...

Answer 5

When installing the #34466NDHR19AAA you can use a nipple like #T3524 and connect it to your the waste valve with some ABS cement #A05-0303 and then a #F02-2103 coupler onto the tank pipe.

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 8

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 9

Hello Michael, Thanks for writing in! Yes, you can recreate the setup you have on your 2014 Forest River R-Pod. You won't find it as one single 1-1/2" to 3" bayonet adapter, but you can put it together with two fittings. For your…

view full answer...

Answer 10

Yes, we do have a suitable part for replacement. The Firestone 24-3582-9210 compressor was discontinued, but Firestone recommends that you replace it with the Firestone Heavy Duty Air Compressor #F9499.

view full answer...

Answer 11

The spare tire retainer would almost certainly interfere with installing the #75210, but we do have a hitch that is positioned a bit differently so it would fit perfectly. The Curt #13250 class III hitch will avoid the spare tire retainer, as shown…

view full answer...

Answer 12

Both of our primary hitch suppliers, Curt and Draw-Tite, show no vehicle listing for a M-B branded Sprinter for model year 2004. Only a Dodge Sprinter is listed, both 2500-series and 3500-series. You can confirm the correct hitch based on the…

view full answer...

Depth Of The LaSalle Bristol And Valterra Sewer Lug To Flange Adapters

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching