B and W Gooseneck Hitch that Fits 2023 Chevy Silverado 2500 Short Bed

Question

Question:

Does the BandW BWGNRK1020 fit a 2023 Chevy Silverado 2500HD? Thanks

asked by: Roger W

0

Expert Reply:

Yes, the B and W Turnoverball gooseneck hitch part # BWGNRK1020 that you referenced does fit your 2023 Chevy Silverado 2500HD short bed as it is a carry over from the 2022 model.

expert reply by: Jameson C

0

Answer 1

Hey Greg, they're not going to work together. The clamps that attach the Air Lift Air Springs like item #AL88341 hang over your frame right where the brackets for the B&W Turnoverball Gooseneck Hitch item #BWGNRK1020 sit. You'll want to…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

B and W Gooseneck Hitch that Fits 2023 Chevy Silverado 2500 Short Bed

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching