Timbren Axle-Less Trailer Suspension For A 5x8 Northern Tool Aluminum Trailer
Updated 10/11/2022 | Published 10/10/2022
Products Featured in This Question
Question:
Hello! I have a 5x8 aluminum Trailer from Northern Tool. I am building a very lightweight tear trailer out of all plastic composites. It will be around about 750 lbs empty and might get close to 1000 lbs loaded. I will be towing with a CX5 or hybrid Rav 4. They are rated at 2000 lbs and 1750 lbs. I want to put a Timbren suspension on it. 1. Do I go with the 1200 lb or 2000 lb suspension. I dont want the 2000 to be too stiff but im nervous getting that close on the 1200. 2. Will a timbren suspension work correctly on a setup that light? 3. Are there any issues attaching steel suspension to aluminum corrosion? 4. Thoughts on brakes? Can I add them with ASR2000S02? I live in coloraodo. It will mostly be used in the rocky mountains. Is that overkill?
asked by: Will
Expert Reply:
I have the perfect solution for your 5x8 aluminum Northern Tool Trailer!
I would recommend going with The Timbren Axle-Less Trailer Suspension System # ASR1200S04 because the 2,000 pound system is overkill. Using this system will give you 2 independent units that can eliminate the need for a thru axle. It will increase the ground clearance and fit any trailer width.
The system has a heavy-duty steel construction that has a black powder coat that resists wear and corrosion. It is easy to install and align and can be either bolted or welded to your trailer's frame. The spindle needs an Inner Bearing # L68149 and an Outer Bearing # L44649. The Easy Grease Trailer Idler Hub Assembly # AKIHUB-545-35-G-EZ-K is the the idler hub needed for the Timbren system mentioned above.
To install brakes The Dexter Electric Trailer Brake Assembly - 7 inch - Left # 23-47 and The Dexter Electric Trailer Brake Assembly - 7 inch - Right # 23-48 is the correct brake setup for you.
I attached a review video link below.
Product Page this Question was Asked From
Timbren Axle-Less Trailer Suspension w/ Idler Hubs - Standard Duty - No Drop - 5 on 4-1/2 - 2K
- Trailer Axles
- Rubber Spring Suspension
- Standard Grade
- Idler Hubs
- 2000 lbs
- 5 on 4-1/2 Inch
- Universal Fit
- No Drop or Lift
- Timbren
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Difference Between an Idler Hub and a Hub/Drum
- Article: Trailer Wiring Diagrams
- Q&A: Difference Between Timbren Axless Suspension Systems T54KV and T99GR
- Q&A: How To Measure Wet Bolts And Suspension Components On Tandem Axle RV
- Q&A: What Inner and Outer Bearings Does 3,500 lb Axle Disc Brake Kit Use
- Q&A: Recommended 2,000 lbs Axle w/ Idle Hubs That Have a 5 on 4-1/2 Bolt
- Q&A: Measurement of Hole Spacing on Torflex Lift Kit # K71-725-02
- Q&A: Bolt Hole Measurements On BTR E-Z Lube Spindle Brake Flange
- Article: Trailer Tire Sizing
- Article: Where to Position the Trailer Axle?
- Article: Double-Eye Trailer Suspension System Review
- Article: Trailer Lighting Requirements
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: How to Raise Your Travel Trailer Height