Availability of 2,000 Pound Timbren Axle-Less System with 6 Hub Face Dimension
Updated 02/18/2025 | Published 08/10/2019
Products Featured in This Question
Question:
In your diagram measurement for part# A20rs545 you show a hubface measurment of 4 7/8 in. I am looking for a part # that would allow measurment to replace 1800 lb axle on a pwc trailer without brakes. In order to do a bolt on installation and not cutoff and reweld my fenders. I NEED A HUBFACE MEASUREMENT OF 6 inches with 5 on 4 1/2 Hhubs any suggestions? Thank you
asked by: JMA
Expert Reply:
For your trailer we have the Timbren Axle-Less Trailer Suspension System # ASR2000S02 that has a 2,000 pound weight capacity and a hub face dimension of right at 6 inches (see attached image).
This particular assembly does not include idler hubs but they can be added with the etrailer.com # AKIHUB-545-35-EZ-K. These hubs feature the 5 on 4-1/2 inch bolt pattern you're needing and includes the bearings, races, and seal.
I have attached a couple short video demonstrations that you can check out as well.
Product Page this Question was Asked From
Timbren Axle-Less Trailer Suspension w/ Idler Hubs - Standard Duty - No Drop - 5 on 4-1/2 - 2K
- Trailer Axles
- Rubber Spring Suspension
- Standard Grade
- Idler Hubs
- 2000 lbs
- 5 on 4-1/2 Inch
- Universal Fit
- No Drop or Lift
- Timbren
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Timbren Axle-Less Trailer Suspension w/ Idler Hubs - Standard Duty - No Drop - 5 on 4-1/2 - 2K
- Search Results: timbren
- Search Results: lock and roll
- Video: Roadmaster Comfort Ride Trailer Suspension Shock Absorber Install - 2021 Keystone Montana Fifth Whee
- Search Results: trailer shocks
- Shop: Timbren Axle-Less Trailer Suspension - Heavy Duty - Long Spindle w/ 4" Lift - 4 Bolt - 2.2K
- Search Results: diode dynamics off road lights
- Search Results: platform rack roof rack
- Search Results: roof rack
- Search Results: kuat roof rack
- Video: Complete Breakdown of the Lock N Roll Articulating Coupler with 30" Extension
- Shop: Timbren Axle-Less Trailer Suspension - Heavy Duty - 4" Lift - 4 Bolt Flange - 2,200 lbs
- Shop: Timbren Silent Ride Suspension for Single Axle Trailers w/ 2-3/8" Round Axles - 2,000 lbs
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Shop: Timbren Silent Ride Suspension for Single Axle Trailers w/ 1-3/4" Round Axles - 2,000 lbs
- Video: Review of the Trailer Idler Hub Assembly for 2,000-lb Axles
- Q&A: Replacement Axle Options for a Harbor Freight 4’x8’ Folding Utility Trailer 62671
- Video: Timbren Trailer Suspension - Cushioned Suspension - TSR2000S04 Review
- Video: In-Depth Look at the Kuat DEK Roof Platform Light Bar
- Video: Complete Breakdown of the Timbren Axle-Less Trailer Suspension w/ Idler Hubs
- Q&A: Do I Have to Remove the Spring Hangers/Stock Saddles to Install the Timbren Silent Ride Suspension?
- Video: Review of Kenda Trailer Tires and Wheels - Karrier KR53 ST175/80R13 Radial White Aluminum - KE77TJ
- Shop: Roof Rack
- Q&A: Recommendations For a Smoother Ride With a 12' Boat Weighing Only 500lbs On Single Axle Trailer
- Q&A: Which Axle for Homemade Trailer
- Q&A: Do the Timbren Silent Ride Suspension Systems Require a Crossmember
- Q&A: Weight of Loadstar ST175/80D13 Bias Trailer Tire Aluminum Wheel # AM3S158 Compared to Steel Wheel
- Q&A: Dimensions Of Timbren Axle-Less Trailer Suspension A20RS545
- Article: Trailer Wiring Diagrams
David
2/18/2025
How flat does the mounting plate have to be for the 2,000 Pound Timbren Axle-Less System... +/- 1/8" or what do you suggest? I assume you shim it to get proper alignment or how do you align? Is there a link to installation instructions doc you can forward please. We'll be welding the mounting plate to a 3" channel that runs the length of the camper trailer. I was thinking of locating a cross member between the two bolt holes towards the pivot end of the axle-less system and welding the mounting plate to that T joint... or do you suggest something else? Thanks, David