Replacement Vent Cover Lid for Fan-Tastic RV Roof Vent Lid 4000BT

Question

Question:

I have a Fan-Tastic 4000BT vent fan in my motor home. I need to replace the outside vent cover I have not been able to find a replacement product that works with my model on your website Can you help? Thanks

asked by: Rick

0

Expert Reply:

The needed replacement part in smoke/tinted is, # FVK1020-19; this fits all 4000 series units like what you have on your motorhome.

expert reply by: Jameson C

0

Answer 1

Yes, it looks like your existing Fan-Tastic Fan model 4000BT is a standard 14" wide x 14" long roof vent so the MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat part #MA00-05100K would fit the opening for your old vent as long as the roof…

view full answer...

Answer 2

Yes, the Replacement Fan Motor Assembly Kit #FVK8017-00 is the correct motor replacement for your Fan-Tastic 4000BT roof vent.

view full answer...

Answer 3

That's because the correct lid you need for your roof vent is the Dometic K8020-09 not #FVK1020-19, but unfortunately that part has been discontinued. So, your only option apart from replacing your unit entirely, is to use a universal lid…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Vent Cover Lid for Fan-Tastic RV Roof Vent Lid 4000BT

Product Page this Question was Asked From

Continue Researching