Correct Replacement Fan Blades and Brackets for 3-Blade AirrForce 42 Hugger Ceiling Fan

Question

Question:

Hello, I have the 2018 artic wolf fifth wheel 315tbh8, and it has the three blade 42” hugger ceiling fan. I’m looking for the replacement fan brackets and blades for it, the fan still runs just need blade components, thank you for your time.

asked by: Joey G

0

Expert Reply:

I was able to confirm that the Replacement Brushed Chrome Brackets for AirrForce RV Ceiling Fan part # 277-000399 and Replacement Blades for AirrForce 42" Hugger Style RV Ceiling Fan part # 277-000398 for cherry/maple or part # 277-94444 for black/villa will also work on the three blade models as well as the four. If you only have three blades you'd just have an extra bracket and blade.

expert reply by: Conner L

0

Joseph

9/1/2025

I have the arctic wolf 2021 291 rl 5th wheel and one of the fan blade arms snapped in the middle of the night. No discernible reason. In regard to your below response, will these fan blade arms (brackets) also work for my fan? All I see is that it is a 42”, I can send you a screenshot of the multiple models on the owners manual it might be.

Robin H.

9/2/2025

@Joseph since it is another Arctic Wolf it is probably the same fan which means these would work. However, we no longer carry these brackets or fan blades so I would reach out to AirrForce directly to see if they still have them and double check fitment.

Joseph

9/2/2025

@RobinHthank you

Cibele

9/3/2025

@Joseph Do you have the contact of airrforce?

Answer 1

Hey Lee, we have exactly what you are looking for with the Progressive Dynamics replacement lower unit part #PD4655V which will allow your setup to be lithium compatible and also doesn't use auto detect to determine battery type and instead…

view full answer...

Answer 2

The Replacement Brushed Chrome Brackets for AirrForce RV Ceiling Fan with Light - Qty 4 #277-000399 does match the 1-1/2" and 3-7/16" measurements provided, so you can use these on your ceiling fan. If you also need new fan blades, the…

view full answer...

Answer 3

The holes that mount to the motor for the Replacement Brushed Chrome Brackets for AirrForce RV Ceiling Fan with Light #277-000399 do measure 1-1/2" on center just like what you have. I have attached a photo that has additional measurements that…

view full answer...

Answer 4

The Replacement Fan Blades #277-000398 are 16-5/8-inches long. They measure 4-7/8-inches wide at their widest point and 4-inches wide at their narrowest point. These install onto brackets like #277-000399 which then attach to the fan itself.

view full answer...

Answer 5

Please see the attached images for wiring diagram and installation instructions for the Furrion Chill Replacement RV Air Conditioner for Furrion Setup, #FR86PR.

view full answer...

Answer 6

The correct replacement motor for your Ventline Exhaust Fan should be the Ventline #BVD0218-00. This 12V DC motor may differ slightly from your original unit, especially if you have an older model. The motor has simply been upgraded a bit from the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Correct Replacement Fan Blades and Brackets for 3-Blade AirrForce 42 Hugger Ceiling Fan

Continue Researching