Do You Carry the Dexter Hub Assembly # 008-247-94 For a 3,500LB Dexter Trailer Axle?

Question

Question:

I need a dexter hub assembly # 008-247-94 Thanks

asked by: Gary

0

Expert Reply:

You are needing the Dexter Trailer Hub and Drum Assembly # 84546UC3-EZ which replaces the Dexter part number K08-247-94.

expert reply by: Bud M

0

Answer 1

It sounds like you may have one of 2 things going on inside your wet bolts. I have seen some instances where some particles/dirt get inside the wet bolt and clog the weep hole the grease is allowed to pass through. You can remove the bolts not taking…

view full answer...

Answer 2

The Replacement Auto-Programmable Controller Panel #LC26TF is the correct replacement for your current Lippert part 366701. I got this information directly from Lippert.

view full answer...

Answer 3

The dimensions I'm seeing for a Suburban SW6DEL show it being 12.69"h x 12.69"w x 19.19"d so the Furrion RV Tankless Water Heater #FR98SR would most likely match up perfectly or require you to trim the opening by 1/8". The…

view full answer...

Answer 4

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Do You Carry the Dexter Hub Assembly # 008-247-94 For a 3,500LB Dexter Trailer Axle?

Product Page this Question was Asked From

Continue Researching