Replacement Rubber Cover for B&W Gooseneck Hitch

Question

Question:

Bought a used truck that has the gooseneck hitch. As we do not use the 5th wheel, when we remove the ball, do you sell a cover for the hole in the bed?

asked by: David A

0

Expert Reply:

If you have a B&W gooseneck hitch that you were searching for parts for then you need the Rubber Cover # BWGNXA1710 if the hitch ball is stowed upside down or the Rubber Cover # BWGNXA1715 if you are completely removing the hitch ball from the gooseneck hitch.

If you end up having a different gooseneck hitch on your truck please let me know what brand you have and I'd be more than happy to help you out!

expert reply by: Jon G

0

Answer 1

The 4.80/4.00x8 tire size is the same as a 4.00X8 tire as long as the load range is the same. The Kenda K371 Bias Trailer Tire, item #AM10004, is a load range C tire. The 4.00 is included in the tire description so those who have the older, no longer…

view full answer...

Answer 2

Yes, the B and W Turnoverball Gooseneck hitch part #BWGNRK1111 that you referenced can be installed in a truck bed that has a slide-in bed liner like you mentioned. You would just need to trim the bed liner around where the ball would come through…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...