Replacement Switch Solution For A Superwinch T1500 Winch

Question

Question:

I have a superwinch t1500 that works great. This past weekend the Switch broke. Do you have anything I can replace it with? Thanks

asked by: David M

0

Expert Reply:

Sure thing!

You can use the:

-Replacement Momentary Rocker Switch for Bulldog Winch 4-Switch Panel w/ Lighted Breakers # BDW20261 with your Superwinch T1500 Winch.

This switch measures 115/16" wide x 1-15/16" high x 1-15/16" deep and is water and weather resistant to IP68 specifications.

expert reply by: Bryce D

0

Answer 1

There is not a wiring schematic provided with the Replacement Switch for Superwinch T1500, EX and X Series Winches, item #SW1519A. You will need to connect the red wire to the circuit breaker terminal and the other side of the circuit breaker should…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 5

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 6

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Thanks for the pictures! To replace the converter in the Magnetek Series 6300A Model 6336 you will want the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 35 Amp item #PD4635V.

view full answer...

Answer 11

There are actually a couple differences between the Curt EZr #C619-648 and the Double Lock #C60712. The visible one will be that the safety chains on the #C60712 are not centered like the ones on the #C619-648. The difference that is not visible is…

view full answer...

Replacement Switch Solution For A Superwinch T1500 Winch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching