Replacement Manual Override Cap For A RAM 3.5K Trailer Jack

Question

Question:

Im looking for a replacement cap for a RAM 3500 lb Capacity, A-Frame Electric Jack.

asked by: Fred G

0

Expert Reply:

I believe you're looking for the Replacement Manual Override Cap for etrailer A-Frame Electric Jack # EJ-3520-BCP.

This will replace the manual override cap on your RAM 3.5K trailer jack, and is black in color.

expert reply by: Bryce D

0

Answer 1

Hey Josh, it sounds like you're describing the Replacement Override Plugs for Lippert Electric Trailer Jacks #LC733924. This plug has that tear drop outer shape you mention, and also has a round inner shape to go in the actual hole.

view full answer...

Answer 2

I have a replacement jack option for you, but unfortunately the motor for your RAM 3500lb A-Frame Electric trailer jack is not a replaceable part. Instead you will need to replace the entire jack. The Electric Jack w/ Footplate - A-Frame -…

view full answer...

Answer 3

Hey Scott! I'm not sure if the Stromberg cap fits but I'm guessing you have a Ram jack that looks like the pictures below. Assuming you do, you can use the Replacement Manual Override Cap for etrailer A-Frame Electric Jack #EJ-3520-BCP which…

view full answer...

Answer 4

Hey Jeremy, I got the replacement cap #e92ZV added to our selection. A picture will be up as soon as we get one in stock and over to the photo department, but this is going to be that teardrop shaped plug just like you have on your jack.

view full answer...

Answer 5

The correct manual override cover for your 3,500lb electric Ram jack is the Replacement Manual Override Cap for etrailer A-Frame Electric Jack #EJ-3520-BCP. For a cover you can use the Ultra-Fab Protective Cover for Electric A-Frame Jacks…

view full answer...

Answer 6

I am sorry to hear that the cover on your Ram 3500lb electric jack broke. There are two different covers based on which jack you have. If you jack is the Electric Jack w/ Footplate - Drop Leg - A-Frame - 25-1/8" Lift - 3,500 lbs - White…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Manual Override Cap For A RAM 3.5K Trailer Jack

Product Page this Question was Asked From

Continue Researching