How Wide Are Frame Clamps On CE Smith Post-Style Guide-Ons for Boat Trailers

Question

Question:

Can you tell me how wide the clamps are once on the trailer from rear to front? I have a dual axle trailer with steps in front and back of the axles

asked by: Darren

0

Expert Reply:

The frame brackets that come with the CE Smith Post-Style Guide-Ons for Boat Trailers part # CE27637 are 4" wide.

expert reply by: Conner L

0

How Wide Are Frame Clamps On CE Smith Post-Style Guide-Ons for Boat Trailers
(click to enlarge)

Answer 1

The guide 65” poles/markers on the CE Smith #CE27637 Guide Ons are only meant as markers to show you where the trailer is. While they can endure some pressure in relation to a straight on approach, off angle pressure which can occur with water…

view full answer...

Answer 2

The 171255UC seal is the same as the Dexter 010-11088/K71-G01-80. We have that same seal available as the Grease Seal Kit- Triple Lip - Inner Diameter 1.719" - Outer Diameter: 2.565" - Qty 2 #DX49CR.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

How Wide Are Frame Clamps On CE Smith Post-Style Guide-Ons for Boat Trailers

Product Page this Question was Asked From

Continue Researching