Distance From Hitch Tube to End of Receiver of Curt Hitch C14082

Question

Question:

Hello, I am looking for a class IV hitch for a custom application. It is a 1985 Chevy C10 frame with a 1956 Chevy 3100 body and bumpers with a K5 blazer rear mounted gas tank. From what I can see, Curt 14082 should work for my frame width and has enough to clear the bumper, but what I need to know is how far does the stinger stick out from the mounting flange? Any dimensions you can provide would be greatly appreciated. Thanks!

asked by: Dan R

0

Expert Reply:

The distance from the crosstube to the very end of the receiver is 8 inches for the Curt Trailer Hitch Receiver # C14082.

expert reply by: Kyle S

0

Answer 1

Buyers Products Class V hitch #3371801102 fits the cutaway cab and chassis version of the 2003 GMC Savana Van. For the cargo and passenger van version their Class V hitch #3371801100 is the correct fit. I am not sure which version of the base vehicle…

view full answer...

Answer 2

The side brackets of the Curt hitch part #C14082 are 9-3/4 inches long so you'd have the clearance needed to fit this on your frame since you have 10 available inches.

view full answer...

Answer 3

From side to side, the mounting holes measure 31-1/4 inches apart, center to center. All three sets of holes are the same distance apart. From rear to front, beginning at the rear of the vehicle the distance from the first set of holes to the second…

view full answer...

Answer 4

Actually several of your pictures did make it through! What you have there is the standard/step bumper on your 1979 Chevy C-10. Deep drop bumpers, also called cowboy bumpers, drop way down. If your truck has an 8 foot bed you can use Curt trailer…

view full answer...

Answer 5

As we have not had a 1973 Ford F-100 in our shop to test fit the available receivers I can only give you the measurements from one of our receivers so that you can see where it will sit on your truck. The Curt Trailer Hitch Receiver #C14082 is…

view full answer...

Answer 6

Hey Zack, thanks for reaching out! The Curt Trailer Hitch Receiver #C14082 has the bolt holes measuring 31-1/4" spacing from center to center. Your truck frame needs to measure 34" outside to outside for this to fit.

view full answer...

Answer 7

Happy to help, and there are a pair of trailer hitch receivers that are a fit for your 1995 Ford F-350 cab and chassis, so long as it has a 34 inch frame width from outside to outside, and I do recommend taking a quick measurement just to be sure.…

view full answer...

Answer 8

When deciding what trailer hitch will fit your RV best practice is to measure from inside the frame beam to the inside of the other frame beam to get the frame width. If you have a width of 18-51" then I recommend the Adjustable Width Trailer…

view full answer...

Answer 9

The trailer hitch options for a 1984 Chevrolet C/K Series Pickup all install in the same manor using holes on the underside of the frame. If there are any brackets present they would need to be removed and are most likely not factory therefore the…

view full answer...

Answer 10

The measurement from the top of the mounting bracket down to the top of the receiver tube measures 5 inches. Curt trailer hitch #C14082 is a custom fit hitch designed to fit the following vehicles: 1973 - 2000 Chevrolet C/K Series Pickup Cab and…

view full answer...

Answer 11

Thanks for the picture of the rear of your 1972 Chevy C20. Based on that it looks like you would need a hitch for a drop bumper setup like the Draw Tite part #41504 so that it would clear the bumper.

view full answer...

Answer 12

The higher the trailer hitch capacity the more steel is used to make the hitch. Higher capacity (10K) hitches like what you are describing usually have a 2-1/2 inch square cross tube or larger (up to 3 inch) so you can measure to determine if you…

view full answer...