Replacement Head Springs for a Curt E16 5th Wheel Hitch

Question

Question:

Head spring replacement

asked by: Brad P

0

Expert Reply:

The Replacement Head Springs for Curt E16 5th Wheel Hitches # C52UR are the correct springs if you have a Curt E16 5th wheel hitch.

If you have a different hitch, please let me know and I can help you find the correct head springs.

expert reply by: Scott S

0

Joe W.

4/30/2025

I have a Husky 16K 5th wheel hitch. I recently removed the head and found a broken return spring. Do you have a replacement for that?

Robin H.

5/11/2025

@JoeW I would reach out to Husky directly. We aren't carrying their parts at this time.

Answer 1

If your Pullrite 4100 is compatible with Industry Standard or ISR rails, as they're sometimes referred to, then it will work great with the rails provided by the Curt #C16200 Universal 5th Wheel Rail/Bracket Kit you'd looked at. If you'd…

view full answer...

Answer 2

The bolt pattern on the Q20 Head #C16530 is different than the bolt pattern on the R16 Slider #C16560. You would need either the A16 Head #C16520 or E16 Head #C16515 to fit your slider.

view full answer...

Answer 3

Good news! I can help you figure out whether or not you will need the Curt Roller Adapter #C16505 to complete your conversion for the Ford Prep Package. If you purchased the E16 Head #C16515, the unit will already come with the bracket #C16505. If…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 11

Hey Kenny, welcome back! The reason for that note is because all of the new systems since 2025 use R32 refrigerant due to EPA regulations. Any 2024 and older systems use R410A and their parts are not compatible with the R32 units. It doesn't mean…

view full answer...

Answer 12

Hey Matt, Furrion typically has 4 wires running to their thermostats and the Chill Cube Thermostat #LC74DX is no exception. The harness you see with the thermostat would plug into the Chill Cube's controller and has 4 wires to extra wire to to…

view full answer...

Replacement Head Springs for a Curt E16 5th Wheel Hitch

Product Page this Question was Asked From

Continue Researching