Availability of 16 inch Trailer Wheel with 6 inch Width and 6 Lug Bolt Pattern

Question

Question:

I’m looking for a couple six lug trailer wheels it says 6kx16 3500 on the back

asked by: Bryce

0

Expert Reply:

Based on what you mentioned what you are looking for is a 16 inch diameter trailer wheel that is 6 inches wide and has a 6 on 5-1/2 inch bolt pattern like the # AM20741 that you referenced. This has a weight capacity of 3,050 lbs but if you needed higher we also have the part # AM20742 which is same wheel mostly but with weight capacity of 3,520 lbs.

expert reply by: Jameson C

0

Answer 1

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 2

After doing some research when fully inflated The 215/85 R16 tire has a diameter of 30.4 inches and a width of 8.5 inches. The Classic Accessories Universal Fit Spare Tire Cover #052963753875 fits tires that have a diameter between 30 inches to 33…

view full answer...

Answer 3

Your ST235/85R16 tire is 31.7 inches diameter, so I recommend the Adco Ultra Tyre Gard RV Wheel Covers - Single Axle - 30" to 32" #290-3952 for a cover with a connector to hold it in place. If you want a cleaner and easier install the…

view full answer...

Answer 4

Yes, unless otherwise stated on the product page for a wheel, it will have a zero offset. So for Dexstar trailer wheel #AM20742 it does have a zero offset meaning the mounting surface of the wheel to the hub is right in the center of the hub. I have…

view full answer...

Answer 5

The tire size you referenced, 235/85R16, has an overall diameter when fully inflated of about 31-1/2-inches. Therefore the cover you referenced, part #052963753479 from Classic Accessories, would be too tight a fit. A better option is the Classic…

view full answer...

Answer 6

From what I can find of your Jingu 17.5 X 6.75 tire is that it has the same wheel size and bolt pattern as the Americana Modular Wheel w/ -0.5 Offset - 17-1/2" x 6-3/4" Rim - 8 on 6-1/2 #AM22461. It also has the same max load capacity of…

view full answer...

Answer 7

Hello Dwayne, thanks for reaching out. Based on my research, the Dexter Trailer Hub and Drum Assembly #8-201-5 will replace the 3160121 drums on your 2003 Airstream Classic. This assembly is designed for 5,200 pound axles and features a 6 on 5-1/2…

view full answer...

Answer 8

The #SP-210275 you were looking at is for a 3500lb axle and is 27" long measured from center of spring eye to center of spring eye. This is the correct spring for your trailer based on the measurements you provided. The next shortest spring…

view full answer...

Answer 9

What most likely occurred when you were driving on the bumpy road with no weight on your utility trailer is the trailer bounced enough to upset the suspension and after it landed it caused the shackle to flip. This tends to happen a lot with trailers…

view full answer...

Answer 10

We have the Conventional Trailer Wheel part #AM20758 which is a 16 inch diameter by 6 inch width wheel with a 6 on 5-1/2 inch bolt pattern and a pilot diameter of 3.65 inch. This should work well for you based on what you listed needing.

view full answer...

Answer 11

Here is a list of our 16" steel trailer wheels which have the 6 on 5-1/2" bolt pattern. We will not have any wheels which have the 95.4mm pilot hole you are needing which should not likely be an issue since trailers will typically use a…

view full answer...

Answer 12

I attached the chart you referenced and it states that when you use a #e54SR spring with a hanger kit part #APS3 the hanger distance should be 24-7/8 inches. The length of a spring when new and not installed on a trailer will be slightly shorter than…

view full answer...

Availability of 16 inch Trailer Wheel with 6 inch Width and 6 Lug Bolt Pattern

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching