Correct Gen-Y 5th Wheel to Gooseneck Pin Box for 2021 Alliance Valor 40v13

Question

Question:

I have a 2021 Alliance Valor 40v13. Looking to get the correct gen y gooseneck pin box. I will attach photo of what is on there now. Thank you.

asked by: Jeff O

0

Expert Reply:

The LCI number 20201330501 you provided relates to a 1621 bolt pattern. It looks like your dry hitch weight is 3,000 lbs and you have a GVWR of 20,000 lbs. Based on this information the correct pin box is the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box - Lippert 1621/1621HD # GY58FR.

expert reply by: Robin H

0

2021 Alliance Valor 40v13 Pin Box.
(click to enlarge)

Answer 1

The Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box #GY58FR will be compatible with the gooseneck ball hitch in your 2016 Ram 3500 Dually. It's rated high enough to handle the GVWR and pin weight of your 2016 Grand Design Momentum…

view full answer...

Answer 2

Hey Terry, from previous customers we have determined that your 2022 Alliance Valor 40V13 has a Lippert 1621 pin box on it so the correct Gen-Y gooseneck adapter would be the part #GY66FR that you referenced which has a 30k trailer capacity and a…

view full answer...

Answer 3

Hey Gatlin, since we know your 2023 Alliance Valor 42v13 has a Lippert 1621 pin box the correct Gen-Y fifth wheel to gooseneck adapter would be the #GY38FR. For a safety chain setup you'd also need the part #GY49GR and you'd have everything…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 12

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Correct Gen-Y 5th Wheel to Gooseneck Pin Box for 2021 Alliance Valor 40v13

Continue Researching