bing tracking image
Customer Service My Orders
  1. Home
  2. Help Videos And Articles
  3. RV Trim Help Hub
  4. RV Trim Q&As
  5. Question 624987
Q & A Icon

Is Tool Needed to Install Rubber Trim for RVs SR78FR  

Published 05/10/2022

Question:

A install tool is mentioned in your description, but I cant locate the tool within your product line. Please help.

0

Expert Reply:

We don't carry a trim tucking tool but they are pretty easy to source elsewhere to help install the RV trim part # SR78FR.

expert reply by:
0
Jameson C

Product Page this Question was Asked From


Q & A Icon

Continue Researching

See More Q&A Expert Answers >>
Explore Expert Info Our Expert
on RV Trim

Videos

Help Articles

Expert Answers

Others Also Watched
In-Depth Review of the Rubber Trim for RVs, Boats, and Utility Vehicle Trim Molding
Hands-On with the Bauer Products T-Handle Lock for Truck Caps
Complete Breakdown of the Rubber Trim for RVs, Boats, and Utility Vehicle Trim Molding
Feature Breakdown: Rubber Trim for RVs, Boats, and Utility Vehicle Trim Molding
B&W Companion OEM 5th Wheel Hitch Manufacturer Breakdown
Comparing Portable Flat Tow Braking Systems - Curt RVi and Blue Ox Patriot
In-Depth Look at the B&W 5th Wheel to Gooseneck Pin Box
Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent Spec Review
No Blind Spots, No Surprises: Furrion Explains Their RV Observation System
Others Also Read
Trailer Wiring Diagrams
Brake Controller 7- and 4-Way Installation Kit (ETBC7)
How to Measure for Trailer Hitch Drop
Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
5 Things to Know About Weight Distribution Hitches
30-Amp and 50-Amp RV Service: What's the Difference?
The 5 Best Trailer Drop Hitches You Can Buy
Brake Controller Installation: Starting from Scratch
4 Steps to Choosing Your 5th Wheel Pin Box
What are the Common Types of Propane Fittings Used on RVs?
Best Vehicles to Flat Tow Behind an RV
Trailer Lighting Requirements
Others Also Asked
Is The Rubber Trim for RVs, Boats, and Utility Vehicle Trim Molding Sold By The Foot?

The Rubber Trim for RVs, Boats, and Utility Vehicle Trim Molding #SR78FR that you mentioned is not sold by the foot, so if you need 33', then I recommend using one #SR78FR and one #SR96ZR for a total of 35'. Since this is a bit longer than…

view full answer...
Replacement Propane Gas Detector for an Atwood 31013 Propane Detector

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...
Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...
Recommended Replacement For An Atwood GC6AA-10E Water Heater

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...
Recommended Bearing Kit for a Lippert 4,400 lbs Axle

For a Lippert 4,400 lbs axle you will need the Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles item #BK2-100. The kits for the 3,500 lbs axles fit the 4,400 lbs ones too so hope this clears up the confusion. You will need one kit per hub.

view full answer...
Fitment of Rubber Trim for Vehicle Trim Molding

The Rubber Trim for Vehicle Trim Molding, #SR78FR is 7/8" as shown in the attached and identified as fitting 3/4" tracks as measured on the inside, such as your measurement is taken.

view full answer...
Can PowerMax AC to DC Converter Charger Be Wired Into 30 Amp Service RV With 4 AWG Wire

Hey John! Yes, a 65A converter/charger like the PowerMax #PM64VR will work well with this setup. Your 30A shore service can easily handle it, and 4 AWG over a 12' run is a solid choice to keep voltage drop low. Just be sure to install a properly…

view full answer...
What Replacement Jack do I Need for My Lippert Level Up with Part Number 343315-RA?

Hello Jerry, Thank you so much for the pictures, they are always most helpful! I am sorry but there is not a seal packing kit, you will need to replace the entire jack. For your Lippert Level Up with part number 343315-RA, you will want the…

view full answer...
Will Lucas Marine Grease Work in Trailer Hub and Drum Assembly #AKHD-545-35-K

Hey Scott, yes Lucas marine grease would be great in the Trailer Hub and Drum Assembly #AKHD-545-35-K that you referenced. That is a perfectly compatible grease that will work great. What kind of trailer do you have and did you have a bearing go out…

view full answer...
Can Victron Blue Smart IP22 12V Battery Charger Work With Solar Charge Controller

Hey Tom! Yes, the Victron Blue Smart IP22 12V Battery Charger #VN65ZR can be added to your system. When you mention working in parallel, I'm assuming you're asking if it can work alongside your solar charge controller. Both the Victron…

view full answer...
Trailer Wiring Recommendation for a 2025 Mazda CX-70

Hey Chuck, thanks for reaching out! I recommend going with the Curt T-Connector Vehicle Wiring Harness #C24ZV for your 2025 Mazda CX-70 because it's a simple Tee-in installation so it's much more simple than getting in behind your tail lights…

view full answer...
Outside Dimensions Of The Replacement Left/Curb Side Leg for etrailer and Ram Hydraulic Jack e63VV

Hey Bill, thanks for reaching out. I just went out to our warehouse and measured the Replacement Left/Curb Side Leg for etrailer and Ram Hydraulic Jack #e63VV. The outer tube is 4-1/2" square. The inner tube with the foot is 4".

view full answer...