Replacement Awning Strip Light for 2019 Keystone Cougar with 2 Solera Awnings

Question

Question:

Need to replace both light strips in awnings. Light strip installs in channel of awning mount against outside wall. Must be narrow in width to fit in this channel. Will this light strip work? LC24PJ Keystone Cougar 2019 , 2 Solera Awnings

asked by: Denise A

0

Expert Reply:

You could use the part # LC24PJ but this is a strip that installs with an adhesive. If you instead were wanting something to fit the track you have on your Solera awning the correct replacement strip would be the part # LC25VR.

expert reply by: Jameson C

0

Answer 1

Good question, and the difference between the standard Solera 12V Power RV Awning Conversion Kit #LC434724 (White) or #LC434723 (Black) and the Solera Smart Arm 12V Power RV Awning Conversion Kit #LC759405 (White) or #LC759517 (Black) is the…

view full answer...

Answer 2

For an LED strip on the roller you could add something like the Optronics Flexible LED Light Strip - Weatherproof - White - 17' Long #UCL90CB. However, you will need to figure out how to run power to the strip and account for the…

view full answer...

Answer 3

Hello Gary. The Replacement Idler Head Mount for Solera Power RV Awnings #LC24VR does not include any additional hardware, so no bearings or bushings. It comes with just the mount piece for the Regal style awnings as shown.

view full answer...

Answer 4

We actually do carry the Replacement Slip Ring Assembly #LC330961 that I believe you are talking about. If you are just wanting to replace the entire idler head then you can do so with part #LC334785 which is in the color black.

view full answer...

Answer 5

Hey Thomas, just the ring disc of the #LC330961 is not available. You'd need to order the part #LC330961 and get the entire assembly.

view full answer...

Answer 6

I have a solution for you, but if you were wanting to add LED lights to your roller, it's unfortunately not going to be as simple as just adding the slip disc #LC330961. The most cost-effective option is just using something like the LED Light…

view full answer...

Answer 7

You would not be able to use just the Slip Ring #LC330961 to retrofit your current idler head to LEDs, you would need to use the Solera Power Awning Idler Head w/ LED Upgrade - Black #LC334785.

view full answer...

Answer 8

There are different replacement mounts for the different sides of your regal style Solera side awning. For the left side - the idler head - you will need the Replacement Mount for Solera Awnings - Idler Head - Regal Style #LC24VR. For the right side…

view full answer...

Answer 9

Since your Solera awning didn't come with the roller tube pre-built to accommodate a light strip, the best thing for your application is to go with the Vista Light LED Kit #LC25VR. This installs where the awning attaches and will actually work…

view full answer...

Answer 10

I contacted the manufacturer with your pictures and what you are needing. They provided the following part as the correct lights that you need: - Replacement LED Light Strip for Solera RV Awning LED #LC423331

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Replacement Awning Strip Light for 2019 Keystone Cougar with 2 Solera Awnings

Product Page this Question was Asked From

Continue Researching