Correct Draw-Tite Hitch for a 2022 Chevy Bolt EUV

Question

Question:

Hi I was wondering if your draw Tite hitch p/n 24956 Fit on the Chevrolet bolt EUV? Thanks

asked by: Daniel B

1

Helpful Expert Reply:

The correct Draw-Tite Trailer Hitch Receiver for a 2022 Chevrolet Bolt EUV is part # DT64GR. This is a bolt-on hitch with a 2" receiver which can be used for towing or hauling bike racks/cargo carriers.

The Draw-Tite Trailer Hitch Receiver part # 24956 is for the EV, not EUV which is different.

expert reply by: Conner L

1

Answer 1

Hello Ben. I've gotta level with you. The Draw-Tite #DT64GR and the Curt #C38DR hitches for the 2023 Chevy Bolt EUV are virtually identical. Sometimes the Curt and Draw-Tite versions of hitches will have some differences such as a different…

view full answer...

Answer 2

The area on the 2017 Chevy Bolt EV that needs to be trimmed is the center, lowest point of the rear fascia that, once trimmed and the hitch installed, won't be visible. The area being trimmed is 3-1/4 inches across and 5 inches deep/tall. I have…

view full answer...

Answer 3

Hello Will, thanks for reaching out. The Draw-Tite Sportframe Trailer Hitch Receiver #DT47GR will not fit the 2022 Chevy Bolt EUV. This hitch is made only for the 2022 and 2023 Chevy Bolt EV and it mounts to the frame rails. The hitch for the EUV…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Correct Draw-Tite Hitch for a 2022 Chevy Bolt EUV

Continue Researching