Can The 8K Fastway WDS Be Upgraded To The 12K System Without Upgrading The Head?

Question

Question:

Presently I have a E2 trunnion wdh with 800 hitch weight with 8000 pound bars. I need to upgrade to 1200 hitch weight with 12,000 pound bars, can I just buy the bars or do I have to buy the head also?

asked by: Ken

0

Expert Reply:

The head that is used on your current system # FA92-00-0800, is the same head on the beefier Fastway e2 Weight Distribution w/ 2-Point Sway Control # FA92-00-1200, so you shouldn't have to upgrade the head.

For the 12,000lb bars, you can use the Replacement Trunnion Spring Bars for Fastway e2 Weight Distribution Systems # FA92-01-1299.

expert reply by: Bryce D

0

Answer 1

Yes, you'd want to replace the spring bars on the Fastway e2 Weight Distribution System part #FA92-00-1200 with the Replacement Trunnion Spring Bars for Fastway e2 Weight Distribution Systems part #FA92-01-1099. These spring bars would be better…

view full answer...

Answer 2

To swap out the 800 lb tongue weight spring bars of your E2 system to 1,000 lb spring bars you would want the part #FA92-01-1099.

view full answer...

Answer 3

You will definitely want to go with the 1,000 lb. bars #FA92-01-1099 rather than the 800 lb. bars #FA92-01-0899. It is better to go with a system that can support you while you are at your heaviest, and deal with what could be a slightly more stiff…

view full answer...

Answer 4

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 5

Hi Michael! I did a bunch of research and found some stuff. You can only tow a 2026 Chevy Equinox front wheel drive with a gasoline engine behind a motorhome, but NOT with all 4 wheels on the ground. You would have to use a dolly, like the Roadmaster…

view full answer...

Answer 6

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 7

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 8

Hey David, it is very possible to replace the Dometic RV AC units you have now with the Furrion Chill Cubes you mentioned but you would need to replace all parts of the system as none of what you have can be reused with the Cubes. So you would need…

view full answer...

Answer 9

Hey Eli! The Advent Air RV Air Conditioner System #ADV92SR you ordered is not compatible with a Dometic Duo Therm. However, it really doesn't matter. This is a new R32 refrigerant unit so it won't be backwards compatible with any of the old…

view full answer...

Answer 10

Hi Shawn! You're dealing with a common issue when installing a MaxxAir II cover #MA76JR on a MaxxFan 4751KS, like the #MA00-04751KSX. Here’s the situation you're running into: -First, the MaxxFan lid opens almost vertical when fully opened…

view full answer...

Can The 8K Fastway WDS Be Upgraded To The 12K System Without Upgrading The Head?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching