Dimensions of Buyers Products 3" I.D. Lunette Ring

Question

Question:

Can I get the dimensions for part number 337BDB1238

asked by: Hector M

0

Expert Reply:

Yep, I can give you the available dimensions of the Buyers Products 3" I.D. Bolt-On Forged Steel Alloy Lunette Ring # 337BDB1238.

It's overall length is 20-3/8", the outer diameter of the ring is 6-1/4" while the inner diameter is, of course, 3". The bar that the ring is attached to on the Buyers Products # 337BDB1238 measures 14-1/2" long, 3" wide, and 1-3/4" thick.

expert reply by: Kyle S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

Hello George, Thanks for writing in. It sounds like the spring bars on your Equal-i-zer system #EQ37120ET are loaded with too much tension, which is why they are staying trapped under the L-brackets and won’t swing outward or lift up easily. This is…

view full answer...

Answer 11

Hey Cliff! When the Roadmaster Guardian XL Rock Shield #RM82DQ is folded it is approximately 45" wide by 31" tall x 9" deep. You can double check on your Grand Cherokee by measuring but I'm fairly certain you won't have any…

view full answer...

Answer 12

Hello Mike, Thanks for writing in! The Blue Ox Base Plate Kit #BLU53FR is a confirmed fit for your 2020 Jeep Gladiator Sport, so you’re on the right track. It’s designed specifically for the Gladiator’s frame, which means your tow bar will line up…

view full answer...

Dimensions of Buyers Products 3" I.D. Lunette Ring

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching