What Replacement Bolt Fits to Attach My Yakima HoldUp Plus 2 Add On # Y02446?

Question

Question:

I am looking for a replacement mounting bolt for Yakima Hold-up + 2. I need the bolt that connects the +2 to the Hold-up.

asked by: Bill M

1

Helpful Expert Reply:

I have exactly what you are looking for. I went ahead and called my tech at Yakima, and she confirmed that the replacement mounting bolt that connects the Plus 2 Add On # Y02446 to the HoldUp is the Replacement Mounting Hardware for Yakima HoldUp Plus 2 Adapter # Y8880128.

expert reply by: Bob C

1

Answer 1

Thanks for the picture of hitch pin, but what was really helpful was actually the set of instructions you have in the background. Based on that you have the first version of the BigHorn which was made around 2001 and the correct hitch pin replacement…

view full answer...

Answer 2

The Replacement Hitch Bolt and Clip for Yakima HoldUp and BigHorn Bike Carriers #Y8890200 doesn't require the clip as the threaded bolt works to secure the rack. If you really want the pin, you can use the Hitch Pin Clip - 1/2" - Qty 1…

view full answer...

Answer 3

Yes, Yakima Replacement Hitch Bolt #Y8880129 is the correct item to secure the HoldUp Hitch Bike Rack #Y02445 in your 1-1/4-inch Class II hitch.

view full answer...

Answer 4

The replacement mounting hardware for the 1-1/4 inch versions of the Yakima HoldUp (2008 to present) is actually #Y8880129. Replacement hardware #8890260 is for HoldUp models that fit 2 inch receivers only.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hello Lou, thanks for reaching out. The hitch pin you are looking for is the etrailer D-Shape Anti-Rattle Locking Hitch Pin for Benton Hitch Accessories #e43JR. This will work with the Benton #B54VR bike rack you mentioned, as well as the #B54FR,…

view full answer...

Answer 9

Hello Rad, thanks for reaching out. Yes, the Replacement Side Rails for Retrax XR Series Hard Tonneau Covers #RTT-82381 are indeed for the 5.5' bed. I do not have a way to look up your serial number to confirm fitment though. If you contact…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

What Replacement Bolt Fits to Attach My Yakima HoldUp Plus 2 Add On # Y02446?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching