Replacement for Discontinued Fulton T3205 Winch

Question

Question:

I need to replace my fulton T3205 winch, I want it to be the same as possibly can? Also is it compatible with strap? Thank you

asked by: Eric F

0

Expert Reply:

The replacement that I recommend for your Fulton T3205 is the 2-Speed Boat Trailer Winch with 20' Strap and Brake - 3,200 lbs # 315-W3200D. This comes with a 20' strap and has a capacity of 3,200 lbs. I attached a review video of this winch for you to check out.

expert reply by: Robin H

0

Answer 1

Yes. The Jif Marine 2 Speed Trailer Winch # will work as a replacement for your old Fulton T3205 winch. It has the exact same 5.1:1 and 12.2:1 gear ratios as the T3205 and also comes with a 10" handle. I've attached a picture for reference…

view full answer...

Answer 2

The replacement I recommend for an Atwood Surge Brake Actuator 85778 is the Demco Hydraulic Brake Actuator part #DM62VR. It has the same ball size, offers a bolt-on install, and has a greater capacity. The only difference is it has an electric…

view full answer...

Answer 3

If the latch on your Atwood surge brake actuator, like part #DM72VR, is fixed in any position start off by using some lubricant like WD-40, PB Blaster, or UltraLube Biobased Spray Lubricant and let it sit for a while. You may have to do this a number…

view full answer...

Answer 4

The correct replacement spring for a Fulton T3205 is the part #4769-28.

view full answer...

Answer 5

First, release the mechanism that holds the coupler onto the ball. It may be a lever or a knob that has to be turned. Some require a dual action move where you would push back or forward on the lever while lifting up on it. If you have done this and…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Replacement for Discontinued Fulton T3205 Winch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching