How To Install The Voyager Camera Adaptor On An RV

Question

Question:

Does this part need to be hooked up to 12 volt? I’m trying to hook up my vom719wp to my rv Aladdin system. All other cameras work fine.

asked by: Eric

0

Expert Reply:

Yes, the Voyager Camera Adaptor # 31300006 is meant to be installed to 12v power.

You'll want to plug the white & yellow RCA plugs into your radio, the red wire to 12v power, and the black wire to a ground.

expert reply by: Bryce D

0

Answer 1

You will only need one of the 12V PWM Filter for RV Backup Camera Systems item #VGR64VR to power your trailers camera system with your Silverado if you wire it behind your main one. We have done it with the main camera successfully here and it has…

view full answer...

Answer 2

I can totally see why that seems like it would help but unless you could ensure that the seal was watertight you'd end up allowing moisture to get into the hitch tube but not able to easily evaporate which would then make potential corrosion even…

view full answer...

Answer 3

Hi Pete, The Voyager Camera Adaptor #31300006 would allow you to connect a Voyager RV Side Camera #VCMS12LGPR to a system with RCA ports. The yellow connector is for composite video and the white is for audio. Since you don't currently have audio…

view full answer...

Answer 4

To use the Voyager RV Side Cameras, Driver #VCMS12LGPR and Passenger #VCMS12RGPR on your motorhome with the RCA connections you will need a Voyager Camera Adaptor - 4 Pin Female Camera Connector to RCA Input #31300006 for each camera. You will also…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

How To Install The Voyager Camera Adaptor On An RV

Product Page this Question was Asked From

Continue Researching