Wiring Schematic for Jensen JWM60A RV Stereo

Question

Question:

I need to replace an AWM950 in a 2007 Winnebago Vectra. Is there a wiring chart to adapt it to the harness for the JWM60A? Thanks,

asked by: Bob L

0

Expert Reply:

Hey Bob, thanks for reaching out!

I have a wiring schematic for the Jensen RV Stereo # JWM60A (see attached), but I don't have one for your AWM950.

You'll just need to wire in the new stereo per function (as opposed to per color) to get everything up and running.

Did your old stereo go out on you, or are you just looking to upgrade?

expert reply by: Jon G

0

Wiring Diagram for Jensen JWM60A
(click to enlarge)

Bob

4/8/2025

Thanks! I found a diagram for the old AWM950 so can easily match functions. On the new unit I'll be ordering soon, it has only one 12v input while the old one has two: one for ignition switch 12v and another for Coach 12v. Can I combine both into the single input? It would still be only 12 volts.

Jon G.

4/8/2025

@Bob Since the JWM60A doesn't have an ignition 12V wire you'll want to connect it to the constant 12V. This could potentially drain your battery over time so you might consider adding a shut-off on it so you can cut power when the RV will be sitting for a long time.

Bob

4/8/2025

@JonG OK, thanks.

Answer 1

Yes, the Voyager Camera Adaptor #31300006 is meant to be installed to 12v power. You'll want to plug the white & yellow RCA plugs into your radio, the red wire to 12v power, and the black wire to a ground.

view full answer...

Answer 2

The Voyager Multi Camera Controller #CSW3 that you referenced is actually the replacement for the CSW3014 that you mentioned as well. It's the latest version with some minor improvements. It's video quality would be as good if not better than…

view full answer...

Answer 3

etrailer is from the US. We are right in the middle near St Louis MO in a town called Wentzville. But we sell products that are made all over. Some from US and some from other countries as well.

view full answer...

Answer 4

There is no adapter harness to convert the wiring from the Jenson JRV212T to the Jensen RV Stereo part #JWM60A. That said, this is actually pretty simple using the attached diagram. All you'll need is some wire crimpers/strippers like part…

view full answer...

Answer 5

The trigger wires on the Voyager Multi Camera Controller for Observation Monitor part #CSW3 are designed to be hooked up to a power source like a turn signal or backup light as that is what will then tell the camera to turn on. There are three…

view full answer...

Answer 6

I did some checking and it looks like the manual transmission 2015 Kia Soul can be flat towed with all 4 wheels on the ground but the automatic transmission versions of the vehicle have to be towed with a tow dolly like the Roadmaster part…

view full answer...

Answer 7

The Timbren #TFRF53A and SumoSprings #SSR-187-40-1 are very similar, which often makes it difficult to decide which is best. Both work independently to help compensate for off-center loads and reduce body roll when swerving and turning corners. They…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Wiring Schematic for Jensen JWM60A RV Stereo

Featured Help Information

Miscellaneous Media

Continue Researching