Can Prodigy P3 Brake Controller Install in 2011 BMW X5

Question

Question:

I have a 2011 X5 with factory trailer harness and want to use a tekonsha primus 90155. It’s not listed as compatible but the connectors look the same.

asked by: Jens

0

Expert Reply:

To install the Prodigy P3 part # 90195 in your 2011 BMW X5 all you need is the install harness part # TK29FR that you referenced. If instead you were referencing the Primus part # TK90160 that is also compatible.

expert reply by: Jameson C

0

Answer 1

All you need to install a Tekonsha brake controller like the P3 part #90195 in your 2021 Porsche Cayenne with the tow package is the install harness part #TK22FR and you'd be set Tod. This directly attaches the controller to the factory wiring of…

view full answer...

Answer 2

All of the P2, #90885 and P3, #90195, brake controllers that we have now and the ones we will get in the future are all the newer versions so you wouldn't have to worry about that for your Porsche Cayenne. Some additional wiring will be required,…

view full answer...

Answer 3

There isn't an aftermarket brake controller pig tail for the 2015 Porsche Cayenne but there is a way to install the P3 #90195. You may need some additional wiring from an authorized Porsche dealer to correctly wire in the controller. Some of it…

view full answer...

Answer 4

Yes the Tekonsha Prodigy P3 Brake Controller #90195 is compatible with your 2022 BMW X5. If you have the factory tow package you can plug it in with Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - BMW #TK29FR.

view full answer...

Answer 5

Yes, we do! To install the Prodigy P3 Brake Controller item #90195 in your 2024 BMW X5 you will need the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - BMW item #TK29FR.

view full answer...

Answer 6

The Tekonsha Plug-In Wiring Adapter #TK29FR is what you'd use if your 2017 BMW X5 has the factory 7-Way connector at the back. Since you're using the Vehicle Wiring Harness #119250KIT that tees in behind the tail lights on your vehicle you…

view full answer...

Answer 7

It's possible that there is a brake controller port under the dash on certain 2019 BMW X5's, but none of the aftermarket manufacturers we carry support this plug. The only option we offer for installing an electric trailer brake controller…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Can Prodigy P3 Brake Controller Install in 2011 BMW X5

Continue Researching