Recommended SnapPads For A Lippert PSX1 Stabilizer Jack

Question

Question:

I just purchased the Lippert PSX1 power stabilizer jacks from you guys order # 112734546 I believe they are part # LC298707 will the SN99FR snap pad kit work with those?

asked by: Shane P

0

Expert Reply:

I actually just went and test-fit SnapPads on the feet of the Lippert High-Speed Power Stabilizer Jack # LC298707 yesterday and discovered that the # SN99FR (4-pack) and # SN77FR (1-pack) are a compatible fit.

expert reply by: Kevin C

0

Answer 1

Hey Tyler, so the difference is the amount of motors that each has. The Lippert PSX2 has two and the Lippert PSX1 like the part #LC298707 has a single motor. The foot print and mounting etc. is exact same so this will fit and work great in place of…

view full answer...

Answer 2

Hey Nicole, congrats on the new 5th wheel trailer! I checked with SnapPad and looked at all the brochure information and I could not find the dimensions of your Sabre's landing gear feet. What I'll need you to do is take a couple quick…

view full answer...

Answer 3

I went out to our warehouse and test fit some SnapPads on the feet of the Lippert High-Speed Power Stabilizer Jack #LC298707 and found that the 6" square SnapPads were a fit. If your 2022 Forest River Vibe travel trailer only has one #LC298707…

view full answer...

Answer 4

You will want to use the K-Source Snap & Zap Custom Towing Mirrors #KS80730 on your 2021 Ram 1500 TRX. These mirror extensions have cutouts for the turn signals, puddle lights and 360 cameras. The CIPA Custom Towing Mirrors #CIP98MR do not have…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Recommended SnapPads For A Lippert PSX1 Stabilizer Jack

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching