What is the Part Number of the Hub from the K08-288-90 Assembly?

Question

Question:

Do sell the Hub separate from the assembly number K08-288-90?

asked by: D T

0

Expert Reply:

Yes, we do sell the hub alone from the Dexter Trailer Hub and Drum Assembly for 9K to 10K Axles - 8 on 6-1/2 - Oil Bath # K08-288-90. That part is the # 008-430-03.

It is important to note that this is the idler hub version that has a different design that comes with the # K08-288-90.

expert reply by: Bob C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 10

Hello Graham, thanks for reaching out. Both the parts you mentioned, the Timbren #T54KV and #TASR5200S03 are 5,200 lb axle-less systems. The difference is the #T54KV is designed for off-road applications with offroad tires while the #TASR5200S03 is…

view full answer...

Answer 11

Hey Al, I have a solution for you but we don't have anything that is a direct replacement for the Kodiak 204 caliper including the DeeMax you referenced. . Since Kodiak was bought out by Dexter it seems they discontinued the 204 caliper in favor…

view full answer...

Answer 12

The attachment bolts for a 5-bolt brake assembly like the part #AKEBRK-6R should be torqued to 30-50 foot/lbs. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn close…

view full answer...