Dexter Replacement Brake Assemblies that are 12-1/4 inch by 2-1/2 inch

Question

Question:

I have a trailer with dexter axles that needs one brake on the passenger side. The sticker that has the part number is worn off. There is a stamping on the backing plate that says dexter 36-119. On the other side it says 70401. It measures 12 1/4” across and the shoe measures 2 1/2”. The drum measures 12 1/4 but the depth is about 3”. I do not need the drum just the electric brake and shoes. Can you provide the correct part number using this? It has 3 mounting holes Thanks

asked by: Rob

0

Expert Reply:

That's an 8k rated Dexter brake assembly for the right hand side of the trailer which we offer with the part # DX52QR for just the one assembly or part # 23-428-429 for both the right and left side.

expert reply by: Jameson C

0

Answer 1

Hey Adina, from what I could find the Norcold N811F requires a cutout that is 60" high x 23-1/2" wide x 24" deep. I would double check your opening just to be sure but based on those dimensions I recommend the Norcold RV Refrigerator…

view full answer...

Answer 2

The number you mentioned is actually not a part number but we do have lift motors that would potentially work. To find out which lift motor you need there should be a number 7 or 17 on the actual motor, which is the RPMs of that motor. If the motor…

view full answer...

Answer 3

The first and easiest thing you should check is that the trailer is being towed level. If the trailer is nose high or low that can cause the equalizers to not sit level. You will need to select the correct rise/drop ball mount so that the trailer…

view full answer...

Answer 4

The brake assemblies that are on your 8k Dexter axles most would be the Dexter Electric Brake Assembly #23-435, the replacement brake magnets for this assembly would be the Replacement Magnet Kit #BP01-301.

view full answer...

Answer 5

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 6

The tow package wiring is located under the dash above where your left knee would be as you were sitting at the wheel. Look for a wiring harness with a white tag on it. GM no longer has a connector, you'd just need to wire the controller directly…

view full answer...

Answer 7

Hey Craig, thanks for reaching out! I believe the Optronics Fleet LED Trailer Tail Lights w/ Grommets #TLL12RK will work as replacements for your 2008 Featherlite 4926 trailer, but you'll need to confirm this on your end. These lights carry the…

view full answer...

Answer 8

The brake assemblies you have are 7k Dexter assemblies that are 12 inch by 2 inch in size. The part number #AKEBRK-7-SA will work as a great replacement set. This includes assemblies for both sides of your trailer that are self adjusting.

view full answer...

Answer 9

The etrailer.com Electric Trailer Brake Kit #AKEBRK-7-SA and the Dexter Nev-R-Adjust Electric Brake Kit # 23-464-465 referenced in your question are both self-adjusting assemblies that will work to replace the existing Dexter brakes on your 7,000…

view full answer...

Answer 10

I have attached for you below an exploded parts breakdown of the Titan/Dico Model 10 Surge Brake Actuator. In regards to the Replacement Top/Bottom Bearing part #T1020900 and Replacement Side Bearing part #T1242700, these work to help stabilize the…

view full answer...

Answer 11

Hi Warren; since you have a Dometic setup the Advent Air Replacement RV Air Conditioner for Dometic Setup #ACDOM135 will work as a replacement. This will be a plug and play installation. If you would like a 15,000 Btu unit we also have the #ACDOM150.…

view full answer...

Dexter Replacement Brake Assemblies that are 12-1/4 inch by 2-1/2 inch

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching