Dimensions of Replacement Gear Kit for etrailer and Ram Round Swivel Marine Jacks

Question

Question:

curious what the dimensions of these gears

asked by: Will

0

Expert Reply:

The Replacement Gear Kit for etrailer and Ram Round Swivel Marine Jacks part # MJ-1000B-GR have a 1/2" inner diameter and 1-1/8" outer diameter.

expert reply by: Conner L

0

Dimensions of Replacement Gear Kit for etrailer and Ram Round Swivel Marine Jacks
(click to enlarge)

Answer 1

Hey Greg, I went out to our warehouse and measured the pins for the Replacement Gear Kit for etrailer and Ram Round Swivel Marine Jack #MJ-1000B-GR and measured 7/8" L x 1/8" wide.

view full answer...

Answer 2

I went out to the warehouse and measured Replacement Cap #MJ-1500B-CP for you. The threaded part has a diameter of 2.08 inches. The overall diameter is 2.19 inches. I have included a picture showing these measurements.

view full answer...

Answer 3

The cap #MJ-1000B-CP is designed to fit MJ-1000B series jacks like #MJ-1206B which has inner tube diameter of 1-3/4 inches. So the cap will fit a 1-3/4 inch tube.

view full answer...

Answer 4

For the etrailer #MJ-1500B-DWL Marine Trailer Jack, if the "bushing" you are referring to is a small fitting that has a 1/2" round hole on the inside and is square shaped on the outside to fit in the square hole in the jack tube, then…

view full answer...

Answer 5

Since we do not carry any rebuild kits for your Knott jack and I do not see any kits available online, I recommend switching to our Round Swivel Marine Jack #MJ-1200B. If this jack needs rebuilt we have the following common replacement parts.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Dimensions of Replacement Gear Kit for etrailer and Ram Round Swivel Marine Jacks

Product Page this Question was Asked From

Continue Researching