Replacement Handle And Crank For A Ventline RV Vent

Question

Question:

Trying to find a handle assembly for this ventline vent.

asked by: Heber

0

Expert Reply:

If your Ventline Vent has a crank handle then you'll want the Replacement Operator, Knob and Screw for Ventline Ventadome Trailer Roof Vents w/ Wedge-Shaped Dome # BVD0462-00. If you have the T-Handle design that slides then you'll want the Replacement Handle Assembly for Ventline E-Z Lift Ventadome Trailer Roof Vents # BVC0580-00.

expert reply by: Kevin C

0

Answer 1

We have actually spoken with Ventline regarding your model AS-13 M-VD0449 in the past and they have confirmed that the correct replacement cover is the part #BVD0449-A03 in Smoke or #BVD0449-A01 in White. The cover measures 14 inches x 14 inches and…

view full answer...

Answer 2

There is more than one way to measure and determine wheel bolt pattern. You can measure across the bolt holes or you can measure to the nearest bolt hole and with that info you'll be able to determine it as well. I attached a link to a help…

view full answer...

Answer 3

Thank you for the photos! From what I'm seeing it looks like you need the Replacement Lift Arm #FVK8011-05 and the Replacement Dome #FVK1020-19 for your main vent. The dome should be an exact replacement while the lift arm doesn't have the…

view full answer...

Answer 4

The only difference between the #RG06-050 and Timken #TMK58ZR is the brand and quantity. Timken is typically considered to be a high quality brand, particularly for their USA made bearings. The #RG06-050 comes with two seals so it is the better…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 11

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 12

We have had a similar question to this come up and we were able to determine that the number AS-13 M-VDO449 that you listed is stamped on the vent cover part #BVD0449-A01. If you are looking for the entire fan setup and not just the cover you would…

view full answer...

Replacement Handle And Crank For A Ventline RV Vent

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching