Bolt-On Tandem Axle Fenders for an Enclosed Trailer

Question

Question:

I need a pair of dual axle fenders for my enclosed trailer bolt on. I want to replace the cheap, thin aluminum fenders that are currently on the trailer. These aluminum fenders are thin, no-step versions, and get bent and torn up, especially when people step or sit on them. I need something alot stronger, a step version. An suggestions?

asked by: Jim M

0

Expert Reply:

I can provide you with some great options for Bolt-on tandem axle fenders. But without knowing your wheel size and how long of a fender you need I can't say for sure which ones you will need.

Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers # HP74VR (15"-16" wheels, 72" fender length) Tear drop style

Tandem Axle Trailer Fenders for Enclosed Trailers # HP57VR (15"-16" wheels, 72" fender length) Non-Tear drop

Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers # HP24VR (14"-15" wheels, 72" fender length) Tear Drop style

Tandem Axle Trailer Fenders # HP22FR (14"-15" wheels, 60" fender length) Non-Tear Drop

All of these are made in the USA and made of a sturdy steel construction. We do not have any tandem style that have a step.

These are just some of our options, I have linked our page of bolt-on tandem axle fenders. You can use your wheel size and fender length to determine which fenders are right for you and use the linked page to get the correct ones. Or you can reach back out to me with your wheel size and fender length and I would be happy to help you find the right fenders.

expert reply by: Scott S

0

Answer 1

Thanks for the photo. Honestly 5 inches of clearance from the fender to the top of the tire is fine if that is what you desire. We normally recommend 4 inches to allow for the suspension travel whether with leaf springs or torsion axles to allow…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 12

Hello Matsubayashi, I wanted to start by letting you know that we do not ship directly to Japan. If you have someone located in the United States, we would be happy to ship the order to them so they can forward it to you. I am showing that your 1995…

view full answer...

Bolt-On Tandem Axle Fenders for an Enclosed Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching