Gen-Y Iron Grip Anti-Rattle Hitch Pin For 2-1/2 Receiver

Question

Question:

Will this pin work on a 2.5 hitch with the 2 inch adapter for my 2 inch shank

asked by: Jon

0

Expert Reply:

For your 2-1/2" receiver you will need the Gen-Y Iron Grip Anti-Rattle Hitch Pin # GY99FR. This pin will fit your 2-1/2" receiver and 2" hitch using a Adapter/Reducer like # 325-GH-007.

The Gen-Y Iron Grip Anti-Rattle Hitch Pin # GY39FR will only fit receivers that have a 2" opening.

expert reply by: Bud M

0

Answer 1

We do have other anti rattle devices that we carry, but nothing specifically designed to limit fore/aft movement. If you have already tried The Blue Ox immobilizer #BX88312, I'm afraid I do not have a more effective anti rattle device that I can…

view full answer...

Answer 2

I may have a solution for you, however we do not have a straight hitch pin available that is compatible with the BOLT Receiver Locks like the part #BL7018448 you were looking at. If the angled end of the pin is wallowing out the hitch pin hole then…

view full answer...

Answer 3

It is not extremely uncommon for the hitch pin hole on a trailer hitch receiver to become oblong after frequent usage. This is usually attributed to frequent back and forth movement of the shank inside the receiver tube opening that in time will…

view full answer...

Answer 4

I just checked with Gen-Y. The Gen-Y Iron Grip Anti-Rattle Hitch Pin for 3" Hitch Receivers - 5/8" Diameter item #GY49FR is rated for 21,000 lbs.

view full answer...

Answer 5

Hey JD, The Weigh Safe Hitch w/ Built-In Scale for 2.5" Hitch #WS88RR uses hitch pic lock #WS54CR, which has a shear strength capacity of 45,000lbs according to Weigh Safe.

view full answer...

Answer 6

I have included an image with the dimensions of the Gen-Y Hitch Anti-Rattle Reducer Sleeve #GY22YR. This will help you to determine if you will have enough room to fit your mud flaps with your specific receiver and hitch.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Gen-Y Iron Grip Anti-Rattle Hitch Pin For 2-1/2 Receiver

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching