Does Tekonsha Wiring Kit 22119 For 2017 Toyota Highlander Have 25-Amp Fuse

Question

Question:

The Tekonsha kit part #22119 has 3 fused connectors, 2 30-amp and 1 25-amp. The instructions in the kit and the videos you made do not show that 25-amp wire being used, at least I havent seen or read anything about it. So, do I need to use it on my 2017 Toyota Highlander XLE? And if so, where?

asked by: William P

0

Expert Reply:

There is not a 25-amp fuse or fused connection with the Tekonsha OEM Replacement Vehicle Wiring Harness w Brake Controller Adapter - 7 Way Trailer Connector # 22119.

The kit comes with two 30 amp fuses, a 15 amp fuse, and a 10 amp fuse. The 30 amp fuses are from the battery connection, and the 15 amp fuse is from the wires that are plugged into the factory connector at the rear of your Highlander.

The only other thing you will need to add to install the # 22119 is the 10 amp fuse in your fuse box, and if you take a look at the linked video, at about the 27:20 mark you can see where that fuse goes.

expert reply by: Kyle S

0

Installation Diagram For Tekonsha OEM Replacement Vehicle Wiring Harness 22119
(click to enlarge)

Answer 1

Thanks for reaching out, Jim! The Roadmaster Single Park Light Diode #RM-690 will work great for this application, and I'm glad to hear others have been successful using it! You'll want to install the diode on the wire connected to the 1…

view full answer...

Answer 2

The Collision System Malfunction error message that you are experiencing on your 2017 Toyota Highlander after installing the Hopkins Reliance Trailer Brake Controller is a result of power backfeeding on the stop light switch wire into the collision…

view full answer...

Answer 3

Wiring in the parking light diode #RM-690 is easy. All you have to do is locate the wire leading to the parking light bulb. Cut the wire and insert the diode in-line with the wiring. The IN side will be the part of the wire that leads to the front of…

view full answer...

Answer 4

If you had a vehicle that needed a diode installed when installing a brake controller you'd need to install the diode like part #RM-690 on the red wire of the brake controller. This prevents the brake controller from back feeding onto the vehicle…

view full answer...

Answer 5

The issue is the wire you ran the red wire of the P3 part #90195 to. We've heard from Tekonsha that a 1 amp diode needs to install on this circuit to prevent the controller from backfeeding onto the vehicle wiring. Or you can use the part #RM-690…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Does Tekonsha Wiring Kit 22119 For 2017 Toyota Highlander Have 25-Amp Fuse

Featured Help Information

Miscellaneous Media

Continue Researching