Is There RV Cargo Carrier that Can Attach to Frame Instead of Bumper

Question

Question:

My 2020 keystone Cougar has no bumper. Id like a rack like this one but want to mount it to the frame or the 5foot long hitch receiver beams. They are welded right to the frame under the fifth wheel. Is there a kit that allows this to mount to the RV frame or hitch support beams? Or perhaps a folding cargo rack made to mount to the frame?

asked by: Tom P

0

Expert Reply:

While we don't have a way to mount the Bumper RV Cargo Carrier # e83YR to the rear of an RV without a bumper a similar solution that could work for you would be a frame mounted carrier that mounts under the RV like with the Lippert part # LC175180 which gives you two bins that mount on underside of the frame that measure 27-7/8" long x 17" wide x 8" tall.

expert reply by: Jameson C

0

Answer 1

The best option we have to add a rear trailer hitch to a Jayco Jayflight is with either a frame mounted hitch, the Adjustable Width Trailer Hitch Receiver part #13703 or a bumper mounted hitch, the Curt RV Bumper Hitch part #C19101. These options…

view full answer...

Answer 2

The RV hitch we recommend the most for applications like your 2020 Jayco Jay Feather 27RL is the Curt #13703 as it fits the widest frame width range of 22 to 72 inches, fits all frame styles, and also can weld or bolt on. It has a 350 lb tongue…

view full answer...

Answer 3

I recommend the Curt Adjustable Width Trailer Hitch Receiver #13703. This receiver will allow you to bolt to an RV frame between 22" and 72" wide. You will need to drill the mounting holes for the frame along with holes in the receiver…

view full answer...

Answer 4

The 24x84 etrailer Cargo Carrier for RV Bumper part #e96ZR can hold a spare tire but there isn't any sort of specific mount for this. The photo attached below is a custom job from a neighbor and I'm not totally sure what they used to create…

view full answer...

Answer 5

Hi Ron; looking at pictures you have the right kind of bumper on the rear of your 2023 Entegra Vision 29S. However, I would go ahead and measure it just to make sure the 24x84 etrailer Cargo Carrier #e96ZR will fit. This is designed to for 4" x…

view full answer...

Answer 6

Hey Mitch! If you can add in material that can handle the weight so it matches a 4" x 4" or 4-1/2" x 4" bumper that will work. A lot of people also choose to weld the #e83YR onto their bumper. This is probably a better solution,…

view full answer...

Answer 7

Yes, the 24x64 etrailer Cargo Carrier for RV Bumper, #e83YR is the built the same as the shorter version but with an extension to increase width. From the images you attached, if you remove the spare tire, you can install the 24x40 etrailer Cargo…

view full answer...

Answer 8

I sure can Tim. The 24x84 etrailer Cargo Carrier for RV Bumper item #e96ZR has three mounting brackets spaced at 14-1/2", 42" center, and 69-1/2". Between the individual slats on the bottom of the carrier is 3-1/2". The carrier…

view full answer...

Answer 9

Hey Bryce, thanks for reaching out, and good question. The Mount-n-Lock Heavy-Haul’r Heavy Duty 4-inch #MNT43VR is basically the same 4" x 4" bumper as the standard 4.0, but with a stronger mounting setup. You’re not getting a bigger or…

view full answer...

Answer 10

Hey Ethan, this is a great question. Basically the part #e99049 is a two-piece carrier that has two brackets that attach to the bumper whereas the part #e83YR is a smaller carrier that has an extension piece in the middle of it that extends it out…

view full answer...

Is There RV Cargo Carrier that Can Attach to Frame Instead of Bumper

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching