Big Dog Alpha MPX Zero Turn Mower Deck Clearance With The Stallion Loading Ramp Set

Question

Question:

Good Afternoon, I have a Big Dog Alpha MPX 54inch mower that I am loading into my barn. Wondering if mower deck will snag at the top where ramp meets barn floor? Barn sits approx. 16inch off ground. Thanks!

asked by: Michael

0

Expert Reply:

The Stallion Loading Ramp Set # 288-07489 will sit on top of the barn floor and with the approximately 4" of clearance the deck has in the lifted position on your Big Dog Alpha MPX mower you shouldn't have an issue with it catching.

expert reply by: Kevin C

0

Answer 1

The biggest difference is the size of the ramps. The Flint Hill Goods #FHG23ZR ramps are 6' long and 14-1/2" wide for each ramp. The Stallion #288-07489 ramps are 65" long and 20-1/2" wide for each ramp. The Stallion ramps are only…

view full answer...

Answer 2

The ramp set part #288-07489 that you referenced has a combined weight capacity of 3,000 lbs for both. Individually each has a 1,500 lb capacity and each ramp has three prongs that lean on the trailer. So each of them is rated for 500 lbs basically.…

view full answer...

Answer 3

I went to our warehouse and laid flat one of the Stallion ramps in the set #288-07489. The tallest point in the arch is where the yellow safety sticker is placed and at this tallest point the height (or thickness, if you prefer) is 3-3/4-inches.

view full answer...

Answer 4

Hey Jeremiah, The Flint Hill Goods Arched Ramp Set #FHG83ZR can be used with a max height of 25". If you need something that works with more height then you'll need the Arched Loading Ramp Set #288-07432-2 which can work with a 35" max…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hello Ben, Thanks for writing in! Yes! The WeatherTech Front Auto Floor Mats #WT54TZ you were looking at are made specifically for the factory vinyl floor in your 2026 Ram 2500. For the rear, WeatherTech does not have a matching custom-fit rear mat…

view full answer...

Answer 7

I spoke with a rep from Gravely and I was informed that there are two models with multiple serial numbers for your Gravely Pro Turn ZX 48" mower. They all have 6" tires, so you should not have any problems with the Loading Ramp Set -…

view full answer...

Answer 8

The rungs on the Stallion Loading Ramp Set #288-07489 that you referenced have 3" gaps between them as you can see in the attached photo. My contact at Stallion confirmed this. If the spacing is too much for you to use and the 3,000 lbs weight…

view full answer...

Answer 9

Hey there Daniel - it really depends on your trailer height and what you’re loading. The 6' RapidRamps kits (part numbers #e47XV for 5–6-1/2' wide trailers and #e67XV for trailers over 6-1/2' wide) give you a gentler approach angle, which…

view full answer...

Answer 10

Yep, that flexibility is built right in, Chris. The ramps slide side-to-side along the index bars on all RapidRamps kits, whether you’re looking at the 5' options (#e37XV for 5 - 6-1/2' wide trailers or #e97XV for over 6-1/2' wide) or the…

view full answer...

Answer 11

I wouldn't worry about the trailer not having fenders. I've pulled a few enclosed trailers that were missing fenders and it didn't affect anything that I noticed. If you get a puddle or it starts raining the tires will fling water so it…

view full answer...