Are the Races Pre-Installed On the Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles

Question

Question:

Are the bearing races already installed.

asked by: Jeff B

0

Expert Reply:

Yes, the races are pre-installed in the Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles part # AKIHUB-545-35-G-EZ-K. You'll simply lube up the bearings and install them along with the grease seal.

expert reply by: Conner L

0

Answer 1

The correct Bearing Buddies to use with the trailer hub #AKIHUB-545-35-G-EZ-K that you referenced are part #BB1980A for chrome plated or part #BB1980A-SS for stainless steel.

view full answer...

Answer 2

For the Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 5 on 4-1/2 - Galvanized #AKIHUB-545-35-G-EZ-K, there isn't an exact size Bearing Buddy available. The Bearing Buddy protectors #BB1980A-SS are the closest to the 1.99 size you need.…

view full answer...

Answer 3

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 11

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 12

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Are the Races Pre-Installed On the Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles

Product Page this Question was Asked From

Continue Researching