Replacement Pivot Pin and Clip For Master Tow Tow Dolly

Question

Question:

Is the tilt pin the same for roadmaster and master tow dollys

asked by: Ken

1

Helpful Expert Reply:

I was able to confirm that the diameter of both the Replacement Steering Pin and Clip # RM-357100-00 and your Master Tow tow dolly are both 5/8" in diameter. You will be able to use the Roadmaster Pin on your Master Tow dolly.

expert reply by: Bud M

1

Answer 1

There is a retainer bolt in the wheel carrier that holds the bushing and king pin in place in the Demco Kar Kaddy SS #DM9713045. You would need to remove the retainer bolt to release the king pin and replace it. This is a part that we do not…

view full answer...

Answer 2

The replacement axle assemblies and kingpins for the Roadmaster Tow Dolly #RM-2000-1 (DISCONTINUED) can be found as part #RM-9210071-91 for the driver's side and part #RM-9210072-92 for the passenger's side. When you replace the kingpin…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Replacement Pivot Pin and Clip For Master Tow Tow Dolly

Product Page this Question was Asked From

Continue Researching