Can I Use Weight Distribution Shank for BulletProof Hitches with Equal-I-Zer Hitch

Question

Question:

Will this adaptor fit the 12k equalizer wd system ,I already have the bullet proof hitch

asked by: Joe N

0

Expert Reply:

Yes. The Weight Distribution Shank for BulletProof Hitches Adjustable Ball Mount # 358WEIGHTDIST can be used with an Equal-i-zer weight distribution system like the # EQ37140ET since the holes on the shank are spaced 1-1/4" apart. This will work well with your Bulletproof Hitch.

expert reply by: Erik B

0

Answer 1

The item you list, #PD4635LIV, is for upgrading a WFCO WF8935 to a lithium battery converter charger. It sounds like you have something from the The WF-8900 Series. Maybe a WF-8955, I suggest verifying your model number. If you do have the…

view full answer...

Answer 2

The Propane Sealing Plug #37207-30425 is a 1/4" male NPT fitting. I verified this with the manufacturer.

view full answer...

Answer 3

Hi Mike yes, the BulletProof Hitches Weight Distribution Shank for 2-1/2" Hitches #BPH75RR has 12" of adjustment in 1 1/4" increments, so it'll work with for a 7" rise/drop.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 8

Hi Donny; after looking at several videos of the trailer it does appear to have a 6 on 5-1/2 bolt pattern with ST225/75R15 tires. The Goodyear Endurance ST225/75R15 Radial Tire w/ 15" Eagle Aluminum Wheel #GY97QB will be a direct fit.

view full answer...

Answer 9

Hey Mike! The Soft Start Kit for Coleman-Mach RV Air Conditioners #CM56RR is designed to work with 45000, 47000, and 48000 air conditioners. Based on those numbers I'm assuming you those are 38000 series, but the model number doesn't always…

view full answer...

Answer 10

Hi Scott, yes, the SoftStartRV part #SSR54FR is the correct soft start kit for your setup. Based on your model number B59516.711J0, you have a Dometic Brisk II 15,000 BTU unit, which is a standard single zone rooftop AC and a perfect match for that…

view full answer...

Answer 11

Hey Michael. The 1976A736 schematic would be the one you would use to install the Soft Start Kit for Coleman-Mach RV Air Conditioners item #CM56RR. However, it's designed specifically for Coleman-Mach Series 45000, 47000, and 48000 air…

view full answer...

Answer 12

It sure is Barry! The SoftStartRV Soft Start item #SSR54FR is exactly what you need for a Furrion AC unit. It'll lower the amps required during startup so you can run other appliances at the same time or power your Grand Design off of a…

view full answer...

Can I Use Weight Distribution Shank for BulletProof Hitches with Equal-I-Zer Hitch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching